IVIN TROY
Impossible is nothing
Skills Acquired at Skill-Lync :
Introduction
22 Projects
Benchmarking
CHALLENGE 1 Comparison between Renault triber, Nissan magnate, Tata nexon, and Mahindra KUV NXT From the given requirements in the question. The car selected are given below # Renault Triber # Nissan Magnite # Tata Punch # Mahindra…
16 Mar 2023 03:26 PM IST
Underbody Coating
UNDER- BODY COATING Underbody coating is a protective layer applied to the underside of a vehicle to prevent corrosion, abrasion, and other forms of damage caused by exposure to various elements. The coating is typically made of a rubber or polymer-based material that is sprayed or brushed onto the undercarriage of the…
18 Mar 2023 09:57 AM IST
Hood design-Week 2
Design of Hood A car hood is defined as the hinged cover that rests over the engine bay of a front-engine vehicle. The car hood protects the engine and connected parts from the elements while providing easy access for repairs and maintenance. The design of a car hood involves several factors, including aerodynamics,…
30 Mar 2023 04:58 PM IST
Section Modulus calculation and optimization
SECTION MODULUS Section modulus is a property used to describe the bending strength of a structural component, such as a car hood. It measures the resistance of a material to bending or deformation. In the case of a car hood, the section modulus is determined by the shape and size of the cross-section of the hood.…
01 Apr 2023 06:57 PM IST
Fender Design - Wheel Arch Challenge
Fender Wheel Arch Challenge The fender wheel arc criteria in a car refer to the space between the wheel and the body of the vehicle. It is an important consideration when selecting tires and wheels for a car, as well as when modifying the suspension or body of the vehicle. This is important to ensure that the tire does…
04 Apr 2023 03:02 PM IST
Fender Design
FENDER DESIGN CHALLENGE Definition of a fender In a car, a fender (also known as a wing in some countries) is a component that is typically located above the wheels and covers the tires. The primary purpose of a fender is to protect the car body from mud, rocks, and other debris that may be thrown up…
18 Oct 2024 03:21 PM IST
Roof Design
Roof Design Introduction An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other external elements. As seen from outside, it is not just a single panel with a specified thickness. It has got reinforcements…
10 May 2023 06:33 AM IST
Design of backdoor
Design of Backdoor Aim To design the backdoor of a car using the given class A surface. Introduction Backdoor or tailgate is a door, located at the rear of the car, which provides access to the luggage compartment. They are hinged to the body and operated manually or electrically according to the car model. The…
13 Jun 2023 06:50 PM IST
Week 7 Challenge - Assembly Workbench
ASSEMBLY WORKBENCH CHALLENGE IS SUBMITTED HERE. PLEASE FIND THE ATTACHED ZIP FILE BELOW.
30 Aug 2024 07:57 AM IST
Week 9 - Challenge 1 - Base Bracket Design
BASE BRACKET DESIGN CHALLENGE In this exercise, a base bracket is designed using the given class A surface. Class A surface The class A surface is then checked for any irregularities or gaps by using boundary tool or other methods. Finding the Tooling Axis Tooling axis is defined as the direction at which the…
16 Nov 2023 06:39 AM IST
Week 9 - Challenge 2 - Switch Bezel Design
SWITCH BEZEL DESIGN CHALLENGE In this challenge, a switch bezel is designed using the given class A surface and a draft analysis is also done for the design. Switch bezels are the parts in a car which contains switches and controls for different functions like window control, door lock/unlock, media…
22 Nov 2023 07:26 PM IST
Week 9 - Challenge 3 - Bumper
BUMPER DESIGN CHALLENGE AIM Create the Bumper Plastic component from the given Class-A surface and find the correct tooling axis and create the draft analysis to check whether the part is manufacturable. INTRODUCTION A bumper is a structure attached to or integrated with the front and rear…
03 Dec 2023 07:03 PM IST
Week 10 - Challenge 1- Attachment Feature Creation (Ribs & Screw Boss)
ATTACHMENT FEATURE CREATION - RIBS AND SCREW BOSS From the given Class A surface, the component should be created as a closed body. Along with that, ribs and screw boss should also be attached to the body as per the design rules prescribed for them. Fig 1. Class A Surface. The given Class A surface is initially…
08 Jan 2024 07:49 PM IST
Week 10 - Challenge 2- Attachment Feature Creation (Dog House)
ATTACHMENT FEATURE CREATION - DOG HOUSE From the given Class A surface, the component should be created as a closed body. Along with that, dog house should also be attached to the body as per the design rules prescribed for them. DOG HOUSE Dog house is an engineering feature used in plastic design.Dog houses…
27 Jan 2024 07:18 PM IST
Week 10 - Challenge 3 - Door Trim Lower with Engineering Features
DESIGN OF HEAT STAKES AND LOCATORS Introduction Heat staking also known as thermoplastic staking is the process of joining two dissimilar materials together. In heat staking we use local heating and cooling to raise the temperature of plastic components and allow plastic reforming…
14 Feb 2024 04:08 PM IST
Week 11 - Project - A pillar Design with Master Section
A PILLER DESIGN WITH MASTER SECTION AIM : To create the A Pillar Design with the master section given as the intersection sketch with the Class A surface accordingly and create the tooling axis and perform the Draft analysis for the final solid part. OVERVIEW : First create a…
29 Feb 2024 07:41 PM IST
Week 12- Final project
FINAL PROJECT - DOOR TRIM LOWER PANEL Aim The aim of the project is to create a CAD model for the door trim panel using the given Class A surfaces and master sections like in the OEMs and Tier 1 companies designing their components. Objectives Check the given Class…
26 Apr 2024 12:10 PM IST
Week 14 challenge
ASSEMBLY OF THE BUTTERFLY VALVEA Butterfly valve regulates the flow by starting slowing or stopping a media. The disc opens and closes with a low torque of 90 and works on any compactible applications. Because of their low cost and maintenance the butterfly valve is preferred over the other valves.The assembly of butterfly…
10 Jul 2024 04:56 PM IST
Advanced Sheet Metal Design Using NX Cad Challenge_5_Odd Shaped Enclosure
CREATION OF AN ODD SHAPED ENCLOSUREObjective To create an odd shaped enclosure using sheet metal workbench in siemens NX Cad.IntroductionCreating an odd shaped enclosure in siemens is the main objective. Here the sheet metal work bench is used for creating the enclosure. The tools and functions like extrude , sheet…
06 Aug 2024 04:19 AM IST
Advanced Sheet Metal Design Using NX Cad Challenge_6_Bracket
BRACKET DESIGNINGIn sheet metal work, a bracket typically refers to a support piece used to hold or secure different parts together. Brackets can be made from various types of sheet metal, such as steel, aluminium, or stainless steel, and they come in various shapes and sizes depending on their intended use.Here are some…
06 Aug 2024 03:41 PM IST
Advanced Sheet Metal Design Using NX Cad Challenge_7_ Metal bracket-II
METAL BRACKET DESIGNING Objective To design a metal bracket using the sheet metal designing and the features used in the sheet metal designing.IntroductionA metal bracket is a structural or decorative component used in various applications to support, secure, or connect different parts. These brackets are typically…
16 Aug 2024 08:36 AM IST
Project - Analysis of a practical automotive wiring circuit
1 The major elements in the diagram are Horn button The "horn button" generally refers to the button in a vehicle that activates the horn, alerting others through a loud sound. It is usually located at the centre of the steering wheel or …
20 Sep 2024 06:38 AM IST
6 Course Certificates
Automotive Sheet Metal Design using Siemens NX CAD / CATIA V5
Fundamentals of Electrical Systems and Electrical Architecture
Academic Qualification
B.Tech
College of Engineering and Management,Punnapra
05 May 2015 - 16 Jun 2020
12th
ST.PETER'S HSS KUMBALANGHI
16 Jul 2014 - 16 Jun 2015
10th
Our Lady of Mercy School, Aroor
05 Jun 2012 - 04 Jun 2013
Here are the courses that I have enrolled
Similar Profiles
Ladder of success cannot be climbed with hands in pocket.
The Future in Motion
Give more than what you get you will get more than what you gave
Avid learner