Mithin SanthaKumar
NA
Skills Acquired at Skill-Lync :
Introduction
15 Projects
Assembly Workbench
This project showcases my skill and experience working in CATIA Assembly workbench After modelling each components of the mechanism in the part workbench , it is assembled and constrained in the assembly workbench
06 Dec 2023 11:10 AM IST
Base Bracket Design
The objective of the project is to Create the Base Bracket Plastic component through the given Class-A surface with the tooling axis for the given Class-A Surface which should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.
06 Dec 2023 11:23 AM IST
Switch Bezel Design
The objective of this project is to Create the Switch Bezel Plastic component through the given Class-A surface with the tooling axis for the given Class-A Surface which should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.
06 Dec 2023 11:56 AM IST
Bumper design
OBJECTIVE : The objective of the project is to create a Bumper Plastic component through the given Class-A surface with tooling axis which meets the requirements of the draft angle and at the end perform the Draft analysis on the model.
06 Dec 2023 11:57 AM IST
Attachment Feature Creation (Dog House)
WEEK 10 CHALLENGE 2 ATTACHMENT FEATURE CREATION (DOG HOUSE) DOG HOUSE : Dog house is an engineering feature used in plastic component designing. these are support features of a plastic component. dog houses are subjected to drafting…
06 Dec 2023 12:05 PM IST
Door Trim Lower with Engineering Features
WEEK 10 CHALLENGE 3 : DOOR TRIM LOWER WITH ENGINEERING FEATURES AIM : Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft…
06 Dec 2023 12:24 PM IST
A pillar Design with Master Section
WEEK 11 - A PILLAR DESIGN WITH MASTER SECTION TOOLING AXIS CREATION : Tooling axis is the direction in which mould travels. basically there are two pieces for mould,one cavity side and one possess projections of the component. the draft angle given for the component for ease of ejection, is drafted with reference to…
06 Dec 2023 12:37 PM IST
Final project : Development of a Door Trim panel
WEEK 12 FINAL PROJECT AIM : Creation of CAD model considering following inputs as like in OEM and tier1 companies Opened seperate part workbench for each surfaces in the given input file and worked on each surfaces induvidually. SURFACE QUALITY INSPECTION : Surface…
06 Dec 2023 12:44 PM IST
Section Modulus calculation and optimization
AIM : To study on section modulus calculation and design a new hood with improved strength SECTION MODULUS : Section modulus represents the strenght of a given component,higher the value higher its strength. it is the ratio of moment of inertia about neutral axis with distance from the outer…
06 Dec 2023 01:42 PM IST
Fender Design
FENDER DESIGN CHALLENGE AIM: To design a front fender of a car by following the given master section as per the design considerations of OEM. FENDER: Fender is a front side outer panel placed above front wheels of a car.its primary purpose is to prevent sand ,mud, rocks ,liquids and another…
06 Dec 2023 01:46 PM IST
Roof Design
ROOF DESIGN CHALLENGE AIM: To design a roof with all the components like front roof rail, rear roof rail, and bow roofs by following the given master sections and the high-quality surface, considering all the design requirements as per the OEM standards. ROOF An automobile roof or car top is the portion…
06 Dec 2023 01:51 PM IST
Design of backdoor
AIM : Use the provided styling surface to come up with a back door design, use appropriate design methodologies, and provide the necessary reinforcements and embosses BACKDOOR : Back door/tailgate is a BiW component found in most of the cars,which provides access to the boot space.it could be hinged at top,side or split type according to the design of the particular vehicle.top hinged back doors will be supported with gas stays.
06 Dec 2023 02:15 PM IST
Butterfly valve
AIM : To assemble the Butterfly Valve by using the sub parts created and apply the GD&T to the Butterfly Valve assembly drawing. Introduction: Butterfly Valve: A butterfly valve is a valve that isolates or regulates the flow of a fluid. The closing mechanism is a disk that rotates. A butterfly valve…
06 Dec 2023 02:28 PM IST
3 Course Certificates
Automotive Sheet Metal Design using Siemens NX CAD / CATIA V5
Academic Qualification
B.Tech
Cochin University of Science and Technology University in Kochi, Kerala
22 Mar 2019 - 11 Mar 2021
Diploma
Maharaja's Technological Institute (MTI) Polytechnic in Thrissur, Kerala
20 Mar 2014 - 16 Mar 2017
10th
Govt THS Shoranur School in Shoranur, Kerala
19 Dec 2013 - 13 Mar 2014
Here are the courses that I have enrolled
Similar Profiles
Ladder of success cannot be climbed with hands in pocket.
The Future in Motion
Give more than what you get you will get more than what you gave
Avid learner