AIM: To calculate the concrete mix design for M35 grade of concrete with flyash.   INTRODUCTION: Concrete mix design is the process of finding the proportion of cement, sand, aggregate and water to achieve desired strength required for the structure. The mix design is done according to structural requirement ,site…

Aim of the project- To sketch a G+1 floor residential plan according to vastu Shastra and to list down the names of structural drawings required to be provided to the site for construction. To assume the size of structural elements (Column, Beam, slab etc) and to calculate the loads from the members as per IS code.  …

AIM: (A) To Create the geometries from P1 to P2 using all the coordinates system methods and P3 to P10 by any one coordinate system (B) To Draw the profile and the trusses using any coordinate system methods. The dimensions are there for reference. 1. Absolute Coordinate System: In this system, all points are established…

AIM:-Creating a Floor plan, Footing detail and Isometric view using AutoCad    Steps for drawing C.S of Load bearing wall over spread footing is as follows. Select rectangle from the ribbon menu Specify the first corner of the rectangle. Enter D for Dimensions. Enter the length: 0.90 Enter the width: 0.25 Select…

AIM- Design and Draft a layout of a residential building with the following details: a. Plot Size: 60’x20’(18.3m x6m)  b. Orientation- Facing East    c. Develop the following: 1. Architectural Drawing (Floor Plan, Elevations, and Sections) 2. Structural Drawing (Column, Bean, Footing Plan) Open…

AIM-1. Create the templates as shown in Figures. Take the size of the title block as per industry standards or you can assume it as per the size of the paper. Use text and attributes wherever required. After creating the title block you need to save it as a block with names: Custom1_titleblock and Custom2_titleblock, respectively.…

AIM: To create the layout of the kitchen and providing hatches to it using the autocad in detail. PROCEDURE: STEP:-1 Below counter plan. First we have to draw the line horizontally with the length of 4300mm. Next draw another line from the previous line with the length of 3200mm Next again we draw the line from previous…

AIM- 1. Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size for the layout.…

AIM-1. Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. Procedure To create a new sheet from application of Auto CAD. Go to the setting and to change the view of the page from Drafting to 3D modeling. Type ,,UN’ to set the units of current format of measure.( feet and inches).…

AIM-1. Create a 3D Isometric View of the building with plan and elevation given. PROCEDURE- First we have to open the autocad and the set the maximum limit and minimum limit on the screen. Here first have to draw the rectangle using the rectangle command, as shown in the figure. Next we have to draw the two windows of…

AIM-Create a 3 dimensional model of the residential building with a rendered view.  PROCEDURE- First step is to open the plan from challenge 8 of residential building Select working space model to 3D modelling Remove all the text from the drawing. Now from the ribbon menu select press pull option. press pull all the…

   AIM-1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level PROCEDURE:-     Step:-1 First we open the revit sofware, and select the ceiling option from the architecture toolbar.     Step:-2…

AIM-1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School I am choosing office building. Result-Structure to be build has been selected.   AIM-2)…

  Aim - To summarize the user interface in TSD for the following items  Project Workspace - Open the Tekla structural designer software and click on New option and the new model workspace will appear Now all the ribbons and menu bars are visible Scene Content - Select window tab and then click on scene content…

1. Create column properties for different types of pedestal members and model in the grids created as per the assignment 1. AIM: To create column properties for different types of pedestal members and model in the grids created as per the assignment 1 Procedure: Launch Tekla Structural Designer 2022 Open the file…

ANS 1) AIM :  To create beam properties for First floor and model the beams. First open the previous week file. Then go to manage property sets under home. The click on new and select members and then steel beams. Off the auto design option, and set to MB350 and click on ok. Under the structure select levels option.…

AIM: Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab as per design Brickwall 150mm thickness Roofing load based on purlin size Ceiling loading 0f 0.3KN per sq m PROCEDURE: Dead load calculations of the the structure as per the structures is given below Dead…

1) Aim - Generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39 m/s Terrain category = 2 Procedure - First calculate load combination  Result - Calculations are done for the wall panel  Step-1 Application of wind load on Model  First Open…

1.Summarize your study for the bending moment, shear force, and deflection diagrams for the elements of the model AIM  To analyse the structure and summarize study for bending moment, shear force, and deflection diagrams for the elements of the model and also display these parameters for our model. PROCEDURE To open…

  AIM: To analyze and design a steel building to 10T CRANE as per IS standard code using TEKLA STRUCTURAL DESIGNER. INTRODUCTION: Tekla Structural Designer is an integrated model-based 3D tool for analysis and design (of both concrete and steel members) in multi-material structures. Features include…

Setup model for RC building design and based on following parameters for cover MEMBERS IN CONTACT WITH GROUND ABOVE GROUND Column 50mm 40mm Beam 30mm 25mm Slab 30mm 25mm Pile cap 75mm   Foundation 50mm     AIM: Setup model for RC building design and based on following parameters for cover MEMBERS IN CONTACT…

Aim - To calculate dead load in design based on IS Code and apply on model. Tools Used - Load Cases, Full Udl , Area Load, Property Window. Calculation - Slab Load = (Model Slab In Software) Finishes Loading (50 mm Thickness ) = 0.05 x 24 kn/m^2. = 1.2 KN/m^2. ( Area Loading ). Brick wall with cement plaster thickness…

Generate seismic loading based IS codal provisions and zone II. Any other data you can assume and input accordingly AIM:- To generate seismic loading based IS codal provisions and zone II. Any other data you can assume and input accordingly INTRODUCTION:- Seismic load are the earthquake load on the structure…

            RESULT :   As per the question  To Based on the analysis design RC column and beam as completed.

Aim: To design the slab and foundation of the model. To outline the thought process for designing of the elements (column, beam, slab and foundations) Procedure: Open the RCC TSD file. Slab design: Go to G.L, uncheck all members other than slab items Click a slab and check its property like reinforcement, bar diameter…

Generate report for the steel building design from challenges 1 – 6 along with the loading summary Aim: To generate report for the steel building design. Procedure: Open the saved Tekla model Now go to the report option from the Ribbon and select model report. Now select the load cases and combinations summary…

Develop general arrangement for the RC office building. Analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. The building to be designed for dead, live, wind and seismic loading.Report of each member to be generated and extract drawings for structural…