Ans 1. AIM- To Calculate the Concrete Mix Design for M35 grade concrete with fly ash CODES FOLLOWED FOR CONCRETE MIX DESIGN- IS 456:2000 IS 3812 (PART 1) IS 8112 IS 9103 IS 10262:2009 INTRODUCTION-  The equations/formulae to be followed here is: Target mean Strength : f'ck= fck+1.65s where, f'ck= target mean…

AIM- Sketching a G+1 floor residential plan as per the Vaastu Shastra and calculate the load acting on the building as per IS code. Points to be noted: Entrance door is facing North direction Living room is in front of the entrance door. Dining room is besides the Living room. Infront of kitchen door. No wall is provided…

AIM- To create the geometries from P1 to P2 using all the coordinates system methods. We need to use the Line tool to create the geometries and to find out the missing dimensions before working on the sketches. Civil Related ProblemsTo draw the profile and the trusses using any coordinate system methods. The dimensions…

To Create a Floor Plan, Footing detail and Isometric view using AutoCAD. AIM 1- To draw the cross section of load bearing wall showing foundation details. Commands used: Line, rectangle, trim Procedure- Create a Rectangle by typing (Rec) command in command box. Specify the first corner point as (5,5). Specify…

AIM- Drafting of various geometries using Chamfer, Fillet tool in AutoCAD Commands used- Units, Line, circle, chamfer, fillet, mirror, trim, move, rotate, annotate. Procedure:  1. Create a new file/sheet. 2. Type command units. Keep decimals to precision 0.00 and insertion scale units as meter. Click…

Creating a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCAD. Challenge 1-  Aim: Residence Plan: To sketch the layout of a residence as given. Commands used- Line, Polyline, Offset, Trim, Erase, Circle Procedure- 1. Open a new autocad file and save it as a new file. Take unit as Engineering…

1. Create a column schedule as shown in the figure. INTRODUCTION 1. Column C1 is provided with 4 bars of 20 mm dia. and 6 bars of 12 mm dia. The 12 mm dia bars are marked with 'a'.2. Column C1a and Column C3 are provided with 12 bars of 16 mm dia bars.3. Column C2 is provided with 8 bars of 20 mm dia and 4 bars of…

Commands Used in this challenge: Line, Xpline, Polyline, Rectangle, Circle, Arc, Trim, Move, Offset, Hatch, Layer, Matchproperties, Multileader, Fillet, Copy, Explode, Dimlinear, breakline, Hide pallets/show pallets (on and off). AIM- To draw a residential building of dimension 60'x20' (18.3m x 6m) with following drawings:…

Aim: To create 1. Templates as shown 2. Doors and placing it in blocks 3. Electrical legend and making it blocks 4. Different types of door 5. Drawing bars, making it as block and then inserting it in table. Commands used: Line, Block, Insert, copy, offset, mirror, text, rectangle, array. 1. Aim to…

1. Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques to dimension the kitchen layout. Also, insert text wherever required. All dimensions are in mm. Procedure: Step 1: units are set to mm limits and limax are also set zoom comand is also used Steps for drawing Below Counter Plan Open Auto…

1. Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size for the layout.…

MAIN AIM: To create 3D model and view of:  Furniture element Isolated footing AASTHO type girder Drop column with panel A wall Commands used: Units, Line, Rectangle, Dim, Box, Extrude, Offset, Subtract, 3d orbit, loft, sweep, cone, region, boundary. PROCEDURE:  Open the AutoCAD, click on workspace switching…

1. Create a 3D Isometric View of the building with plan and elevation given. AIM:- To create a 3D isometric view of the given building with plan and elevation. INTRODUCTION:-  An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface. One…

AIM:  To create a 3D rendered model for a Residential Building in AutoCAD INTRODUCTION: The main objective of this project is to understand about to create a Plan in 2D, then convert it into 3D using AutoCAD 3D, applying materials and rendering. AutoCAD is primarily used for generating 2D sketches. While it is…

1. AIM: To Summarize the user interface in TSD with the for the following items: - Project Workspace – How to access and usage Scene Content – Demonstrate the use of scene content Create two scene views Loading drop list- How to access Properties windows – how to access and usage 1.Project Workspace:…

1. Create column properties for different types of pedestal members and model in the grids created as per the assignment 1. AIM: To create column properties for different types of pedestal members and model in the grids created as per the assignment 1 Introduction: The pedestal is the block of concrete that supports…

1. Create beam properties for First floor and model the beams. AIM: Create beam properties for First Floor and model the beams. Introduction: Using Tekla Structural Designer (TSD) we need to create the beam properties for First Floor similarly like the last challenge using the data from the attachments provided. Procedure:…

1. Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab as per design Brickwall 150mm thickness Roofing load based on purlin size Ceiling loading 0f 0.3KN per sq m AIM : To Calculate dead load in design report based on IS code and apply dead load on…

1. Aim - Generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39 m/s Terrain category = 2 Procedure - We need to first calculate load combination.  Result- Calculations are done for the wall panel. 2. Aim - Based on the above calculation apply the…

AIM: Summarize your study for the bending moment, shear force and deflection diagrams for the elements of the model PROCEDURE:  Initally open the Tekla file you saved previously. After opening the file->We start the Seismic data in the structure To set->go to Load panel->Under seismic load go to Seismic wizard…

AIM: To analyze and design a steel building to 10T CRANE as per IS standard code using TEKLA STRUCTURAL DESIGNER. PROCEDURE: Initially open the Tekla Structural Designer software. Now click on New option to create a new model workspace. Using the Model Ribbon using the grid line and Quick…

1. Setup model for RC building design and based on following parameters for cover MEMBERS IN CONTACT WITH GROUND ABOVE GROUND Column 50mm 40mm Beam 30mm 25mm Slab 30mm 25mm Pilecap 75mm   Foundation 50mm AIM : To setup model for RC building design and based on the given parameters for cover. PROCEDURE : …

Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab thickness as per the design Brick wall load Roofing load AIM- To calculate the dead load in design report based on IS code and apply dead load on the model. PROCEDURE :  Finishes of 50mm Slab thickness as per…

1. Generate seismic loading based IS codal provisions and zone II. Any other data you can assume and input accordingly Aim: To generate seismic loading based IS codal provisions and zone II. Procedure: Open the previously save Tekla model Now go to the load cases and add the seismic load case, and click ok Now go to the…

Based on the analysis design RC column and beam. AIM: Based on the analysis we need to design RC column and Beam. Procedure: Open the tekla model and run the analysis Select any of the column member and right click on it Then select the interactive design- static from the given option Check the errors and check again…

Aim: To design the slab and foundation of the model. To outline the thought process for designing of the elements (column, beam, slab and foundations) Procedure: Slab Design Open the previous RCC Tekla file. Slab design: Go to G.F (Ground Floor), uncheck all members other than slab items Click a slab and check its…

1. Generate report for the steel building design from challenges 1 – 6 along with the loading summary Aim: To generate report for the steel building design. Procedure: Open the Tekla model saved after Challenge 6. Now go to the report option from the Ribbon and select model report. In chapters and options under…

Develop general arrangement for the RC office building. Analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. The building to be designed for dead, live, wind and seismic loading. Report of each member to be generated and extract drawings for structural…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level Ans-  AIM: To model a Ceiling from the architecture tab above the walls at the first-floor level. Procedure: First we open the revit sofware, and select the ceiling…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School Ans- I want to build a Multi-Unit Residential Apartment 2) Assume reasonable assumptions…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. Ans-  Aim: To create a set of sinusoidal points, a curve and a surface out of the curve using dynamo. Procedure: Initially, open the architecture template of Revit software and go to manage tab. In manage tab…

Question 1 1 Write the steps involved to upload a .std file through web mail? Ans- The steps involved to upload a .std file through web mail are as follows: a) Login to your web mail account. Go to compose new mail b) Attach the .std file from the location saved in pc. c) Type a message along with the attached file in…