Pdf format 

iam solving the question in pid control        % This file contains the dsign parameters to model a DC motor J = 0.01; % moment of inetria of the rotor in kg-m^2 b = 0.1; % Motor viscos friction constant in N-m^2 Km = 0.01; % back emf conatant in v/rad/s. Kt = 0.01; % Motor torque constant Ra = 1.0;…

  The Double-Acting Hydraulic Cylinder block in the scissor hoist contains mechanical and hydraulic subsystems. The mechanical subsystem models the piston and barrel. A Prismatic Joint block provides the translational degree of freedom needed for piston extension and retraction. The piston's range of motion is constrained…

  data is taken from advisor and downloaded done in drive cycles also  program files and simulink files is attacehed in browse formate

Detail explained and Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium-ion cells.

There is a different kind of Controllers, one is the Supervisory Controller and the others are the Control Units. The input data for the Control Units come from the Supervisory Controller. The supervisory Controller has conditions to follow which directly depend on the Driver's action and based on the same, the control…

The high voltage battery is one of the most important components of a battery electric vehicle (BEV). The battery parameters have a significant influence on other components and attributes of the vehicle, like: maximum traction motor torque maximum regeneration brake torque vehicle range vehicle total weight…

Study 2:-What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation ?  coulomb counting:- The Coulomb counting method measures the discharging current of a battery and integrates the discharging current over time in order to estimate SOC . Coulomb counting…

DEFINIG ELECTRIC PARAMETER FLOW CHART. CONNECTOR DEFINATIONS IN CATIA V5 Deutsch DT06 – 08SA Connector connection point: Create midpoint on the contact face which will be normal to wire bunddle insertion. Create Axis System with respect to the point which we have created and defining the axis direction as shown below,…

Steps. Once the File is Downloaded, Open the File Using CATIA V5 Using the Part design model, we define entry, Exit, Base points, and Planes After determining the points and planes open the file in Electrical Part design Now we need to define the part as a Support using the Define support Part Here we use the Required…

DT06-2S: - First imported models from given link. Open mechanical part design, Defined the middle point with of the mide point, On the connector side and bundle side. Given axis system to connector side, Rotated X Axis and given the 90-degree y axis the n coincidence now changing the work bench electrical part design.…

1st Connector of Harness B:   In the Above figure We Have Taken from given source & Merged into Catia V5. 1.Go to the Part design workbench & Taking A middle Point From The Connector Connecting Side As Well As Bundle Connecting Side. 2.Taking the axis Origin of Connector connecting Point. 3.Adusting the y-axis…

Step - 1: Create a product file and navigate to the Electrical Harness Flattening for wire harness flattening option and save it in the same location where the wire harness or routing assembly is stored. Define the 'Harness flattening parameters' in order to flatten the required wire harness assembly. While defining the…

Statement of assignment: Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available connector 3D data can be used, or you can…

Automotive Wiring Harness for Backdoor Aim: To create a Wiring Harness for the Backdoor, Flatten the same for the production and apply the necessary protective covering using CATIA V5 software. Objective: The objective is to route the wiring harness for the backdoor and flatten the wiring harness to Drawing for…

AIM:  Based on the concepts you have learnt during the forward kinematics routine, go ahead and write code that can solve an otto cycle and make plots for it. Here are the requirements Your code should create a PV diagram You should output the thermal efficiency of the engine.   OBJECTIVE: To solve and find out…

AIM:  TO SIMULATE THE TRANSIENT BEHAVIOR OF A SIMPLE PENDULUM AND TO CREATE AN ANIMATION OF ITS MOTION. OBJECTIVE :  To write a program in Python that solves the second-order ODE corresponding to the motion of a simple pendulum and to plot its angular displacement and angular velocity wrt time. To create…

  What does popt and pcov mean? (Watch the video to get some context) In the curve fitting code, the variables "popt" and "pcov" are defined to the curve fit function. The first variable, "popt", stores and extracts the coefficients of the curve fitting function into an array, with respect to the general polynomial…

OBJECTIVE: To perform Data Analysis. Plot a graph between any two Column vector. Calculate the area under the P-V diagram. Calculate the power output of this engine. Calculate engine specific fuel consumption.   PROBLEM STATEMENT: Data visualizer Your script should take column numbers as the input and plot the respective…

Aim) The main aim is Design the Simulink model of BOOST converter and determine the Losses of Converter and efficiency of the Converter. Answer) BOOST-CONVERTER: -         A boost converter (step-up converter) is a DC-DC power converter that steps up voltage (while stepping down…

AIM: - The main aim is Design the 3 Phase Inverter using Simulink and Controlling the 3 phase Squirrel Cage Induction motor, using V/F method from 3 Phase Inverter. Answer: - Three-phase inverter is used to change the DC voltage to three-phase AC supply. Generally, these are used in high power and variable frequency…