Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad

1st question: find the stiffness co efficient of the system.     In the given figure there are three degree of freedoms as fiven 2 are rotational and one is translate motion. Lets consider the unit displacement. Given conditions L=2h EI of beam=EI of column For the displacement u1 1)K for the column in translation=2x …

FAILURES AT JOINTS: In general the failures occur due to low stability,strength and inadequate durability. 1ST QUESTION Fig:a In the figure the failure occur at the edge of the beam and the failure occur only for the beam this typwe of failure occur due to moment in the beams in the opposite direction. It will not repaced…

1ST ANS:EXPORTING THE REVIT MODEL. After the completion of the structural analysis of the model using structural analysis next the model is exported to Navisworks for the view and schedule purpose. For exporting the model from revit to naviswork we need to install naviswork export with the appropriate version. After the…

1ST ANS:SIN CURVE CREATION: Step:1 For the creation f an sin curve first we have to create a set of points. For he creation of the points range option is taken and then for the for the values of start,end,phase code block is used to assain te values for the curve or we can use slider to assin the values. Step:2 After the…

1ST ANS:USING OF SHORTCUT KEYS. By using the shortcut keys like bx,mm,st etc the modefications are made and the results are attached in the answer. 2ND ANS:ScheDULE OF THE ITEMS:  Step:1 first the schedule option is taken from the architech tab and the option is selected as door for the schedule of the doors. Then…

1ST ANS:HVAC SYSTEMS HVAC system is defined as heating ventilation and air conditioning. HVAC system is used to manage the temperature of the building. It is used to optimize the room temperature like when it is summer it reduces the heat and makes the room cool and in the winter it will be adjusted to heat.   2ND…

AIM: DESIGN OF RESIDENTIAL BUILDING. Stpep:1 From the file menu new archithech sheet is taken for the modeling of the building. The units are converted into feet by using  the option project units from the manage toolbar. Using the line tool layout is  drawn for the development of the modeling. All the design…

WORKING USING COLLABORATION TOOL STEP:1 A new architech templete is taken and is saved with the appropriate name say (collb arche) After saving the sheet grids are prepared in the both directions i.e transfers and longitudinal. After the creation of grids the co-ordinates are takes for taking co ordinates set co-ordinates…

1ST.ANS: BUILDING CODES ESSENTIAL FOR MODELING  For the design of the buildings or any type of construction the particular codes are to be followed based on the no.of reasons. The codes are made based on the type of the terrine and the weather conditions for the structural design. Based on the experiments the codes…

 PROCEDURE FOR THE PROJECT: After the revit is open we can see the sample project options like archetech,structural etc the apropreate file is taken but for now as for our requirement,new option is selected a window is displayed showing the project templet type for my convience imperial templet Is taken by using the…

 PROCEDURE FOR THE PROJECT: After the revit is open we can see the sample project options like archetech,structural etc the apropreate file is taken but for now as for our requirement,new option is selected a window is displayed showing the project templet type for my convience imperial templet Is taken by using the…

 PROCEDURE FOR THE PROJECT: After the revit is open we can see the sample project options like archetech,structural etc the apropreate file is taken but for now as for our requirement,new option is selected a window is displayed showing the project templet type for my convience imperial templet Is taken by using the…

 PROCEDURE FOR THE PROJECT: After the revit is open we can see the sample project options like archetech,structural etc the apropreate file is taken but for now as for our requirement,new option is selected a window is displayed showing the project templet type for my convience imperial templet Is taken by using the…

AIM:         DRAWING THE  3D PLANS OF  RESIDENTIAL BUILDING AND RENDERING  USING 3D AUTOCAD SOFTWARE. DETAILS OF PROJECT: THE GIVEN 3D PLANS ARE DRAWN ACCORDING TO THE DIMENTIONS AND THE STEP BY STEP  PROCESS IS GIVEN BELOW. PROCDURE: A basic residential building is…

AIM:         DRAWING THE GIVEN 3D PLANS  USING 3D AUTOCAD SOFTWARE. DETAILS OF PROJECT: THE GIVEN 3D PLANS ARE DRAWN ACCORDING TO THE GIVEN DIMENTIONS AND THE STEP BY STEP  PROCESS IS GIVEN BELOW.   PROCDURE:         For the given drawings…

  AIM:         DRAWING THE GIVEN 3D DRAWINS  USING 3D AUTOCAD SOFTWARE. DETAILS OF PROJECT: THE GIVEN 3D PLANS ARE DRAWN ACCORDING TO THE GIVEN DIMENTIONS AND THE STEP BY STEP  PROCESS IS GIVEN BELOW.   PROCDURE:         For the given…

AIM:        LAYOUT OF THE PREVIOUS DRAWINS DETAILS OF PROJECT: THE PREVOIUS DRAWINGS ARE TAKEN IN A NEW LA OUT WITH THE SOVEN SCALE AND GIVEN DIMENTONS PROCDURE:         First a new lay out is taken by using the option in the act at he bottom left corner.MARCH.DWG TEMPIET IS USED.…

AIM:         DRAWING THE GIVEN ELEVATION AND SECTION USING AUTOCAD SOFTWARE. DETAILS OF PROJECT: THE GIVEN DRAWING CONSIST  KITCHEN ,SECTION OF ELEVATION DETAILS AND THE STEP BY STEP  PROCESS IS GIVEN BELOW. THE GIVEN PROJECT IS ABOUT ELEATION OF THE BUILDING IN THE CHALNGE…

AIM:         DRAWING THE GIVEN DESIGNS USING AUTOCAD SOFTWARE. DETAILS OF PROJECT: THE GIVEN PLAN CONSIST OF A  DOOR DESIGNS AND BBS  DETAILS AND THE STEP BY STEP  PROCESS IS GIVEN BELOW. PROCDURE:         For the given drawings the units…

AIM:         DRAWING THE GIVEN PLAN USING AUTOCAD SOFTWARE. DETAILS OF PROJECT: THE GIVEN PLAN CONSIST OF A FLOOR PLAN OF A BUILDING ,FOUNDATIONS DETAILS,AND ELEVATION DETAILS,SECTION SHOWING BEAMS,COLUMS,FOOTING AND BRICK WORK AND THE STEP BY STEP  PROCESS IS GIVEN BELOW. GIVEN…

AIM:         DRAWING THE GIVEN PLAN USING AUTOCAD SOFTWARE. DETAILS OF PROJECT: THE GIVEN PLAN CONSIST OF A FLOOR PLAN OF A BUILDING ,SECTION,AND ELEVATION DETAILS AND THE STEP BY STEP  PROCESS IS GIVEN BELOW. PLAN CONSIST OF 3 FLOORS AND THE SECTION OF THE PLAN ARE GIVEN WITH DETAILS…

AIM:         DRAWING THE GIVEN PLAN USING AUTOCAD SOFTWARE. DETAILS OF PROJECT: THE GIVEN PLAN CONSIST OF A FLOOR PLAN OF A BUILDING ,FOUNDATIONS DETAILS,AND ELEVATION DETAILS AND THE STEP BY STEP  PROCESS IS GIVEN BELOW.   PROCDURE:        …

AIM:         DRAWING THE GIVEN TEXT AND TABLES USING AUTOCAD SOFTWARE. PROCDURE:         For the given drawings the units are set according to the requirements. The limits of the  page are set to 1000,1000 in x y directions respectively. Dimention…

AIM:         DRAWING THE GIVEN RESIDNC LAYOUT ,SEATING PLAN AND TIOLET PLAN USING AUTOCAD SOFTWARE. PROCDURE:         For the given drawings the units are set according to the requirements. The limits of the  page are set to 1000,1000 in x y directions…

AIM:         DRAWING THE GIVEN PLAN USING AUTOCAD SOFTWARE. PROCDURE:         For the given drawings the units are set according to the requirements. The limits of the  page are set to 1000,1000 in x y directions respectively. Dimention style commond…

The given floor plan is drawn using autocad 2022  First new page is taken and the required settings are done. The units are set by using the commont units  After the units the page limits are set as per the requirement. For stright lines F8 is enabled. For the editing of snap and grid tools drafting settings…

THE given drawings are drawn as per te given dimentions are explained bellow New cad sheed s taken from the file menu Units are set to decimial  limits of the page are given approxmately By using coordenate system the drawings are drawned. F8 is enable for the strigth lines the grid spacing is taken as 1,1 in both …

DRAWINGS REQUIRED FOR SITE: 1.Center line marking 2.Foundation drawings 3.plenth beams drawing 4.BBS 5.Beams and columns drawing. 6.Slab details. 7.Electrical and pumbing.   LOADS OF THE STRUCTURE: All columns 0.2X0.3m (height of ech column=8m) All beams  0.3x0.45m (all the beams are same size) Slab thickness…

AIM:      CALCULATING THE DESIGN MIX FOR M35 CONCRETE WITH FLY ASH AND M50 WITH OUT FLY ASH AS PER IS CODES.      GIVEN DATA:(ASSUMED)      1.0PC 43 GRADE CEMENT(IS8112)      2.20MM SIZE AGGREGATE,ZONE 1 FINE AGGRGATE.      3.EXTREME ENVIRONMENT…