Hood design-Week 2

AIM:Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Objective:The routing of the backdoor of the car is done in this particular challenge, by considering all industrial standards and procedure.The flattened view and its 2D representation needs to be done in this challenge.Industry…

Aim: Route the wiring harness for the Bugatti V16 Engine assembly and prepare flatten-view drawing in CATIA V5. Objective: The objective of this project is route the wiring harness and proceed with the flatten-view drawing for the Bugatti V16 engine. All types of packaging rules and constraints have to be considered while…

FLATTENING ASSEMBLY OF PREVIOUSLY CREATED HARNESS ROUTING OBJECTIVE:Create the flattened view of the previously created harness assembly and then generate its 2D representtion in catia drawing window itself, and assigning different visuals for the protective covering. INPUT: HARNESS ASSEMBLY  STEPS YOU NEED TO FOLLOW…

ROUTING THE DEUSTCH CONNECTORS  AIM-To route the the listed connectors according to the diagram provided for positioning of the connectors and their respective routing,add the connectors in the catalog and even provide the corrugated tube for the two connectors connecting branch check the bundle connectivity to ensure…

ROUTING AND CONNECTING THE HARNESS A AND HARNESS B. Objective: Define all the input connectors electrically by using the electrical part workbenchand later create the catalog for storing of all the connectors, later Route the harness A and harness B separately in individual product file and connect them electrically by…

CHALLENGE FOR CATALOG CREATION, COT TUBES , DEFINING P-CLAMP AND BACKSHELL ELECTRICALLY. OBJECTIVE: Create the cot tubes for various diameters listed in input and add them to cataog, define the P-Clamp electrically and list its electical properties and define the Backshell electrically and list its electrical properties.…

      OBJECTIVE:Use the given cad files of connectors and clips as input and define them electrically, also define all the various connectivity points related to the connector and clip. CONNECTOR: Automotive electrical connectors are specifically designed for use in automobile electrical systems. Automobile…

FENDER WHEEL ARCH CHALLENGE FENDER WHEEL ARCH Wheel Arch is the semi-circular part of the fender positioned above the wheel of the vehicle. The design of the wheel arch of the fender should be such that it must shield wheels and protect both passengers compartment and pedestarians from the projection of watr, mud and stones.The…

BENCHMARKING CHALLENGE  OBJECTIVE:Benchmarking study of the vehicles which falls under 8-10 lakhs and provide with the best fit for the person with all the consideration and features following the place, use and cost.   BENCHMARKING: Benchmarking involves a structured comparison between similar products, services…

BACKDOOR CHALLENGE OBJECTIVE TO CREATE PROPER STYLING SURFACE WITH THE GIVEN CLASS A SURFACE CREATE THE SEALING FLANGE WITH RESPECT TO THE INNER PANEL. PROVIDE THE EMBOSSES FOR THE GAS STAY,WIPER MOUNTING,HINGE AND LATCH &STRIKER. CREATE SEPARATE PARTS FOR THE REINFORCEMENTS. DRAFT ANALYSIS OF THE PANEL. HEMMING OPERATION…

SECTION MODULAS CALCULATION OBJECTIVE: To calculate the section modulas of the previously designed hood . To generate new design with improvised section modulas by optimizing the design. SECTION MODULAS:   The section modulus of the cross-sectional shape is of significant importance in designing beams. It is a…

                                                                                                                      ROOF CHALLENGE OBJECTIVE: Study the curvature of the roof class A surface. Create the flanges of roof wrt the master section. Create the front and rear roof rails following the master section. Create the…

                                                                                                  FENDER DESIGN   OBJECTIVE: Creating the fender flanges from the fender skin data received as input,later assigning the points for various fender mountings. Follow the master section for the drip area mounting received as input…

                                                                                           …

 FINAL PROJECT                                                                                                            DOOR TRIM DEVELOPMENT  INPUTS: CLASS A surfaces of the DOOR ARM REST, MAP POCKET, BOTTLE HOLDER and LOWER SUBSTRATE. Master section for the attachment features. Push clips for the assembly. OBJECTIVES:…

                                                                                           …

                                                                                            DOOR…

                                                                                           …

                                                                                     PRODUCT WORKBENCH CHALLENGE…

                                                                          DESIGN OF SCREW BOSS AND DOG HOUSE   OBJECTIVES: Create…

                                                                                          RIBS…

 DRAFT ANALYSIS ON SWITCH BEZEL  AND CREATING THE CORE AND CAVITY BLOCKS    OBJECTIVE: Analysing the class A surface given as input. Create the tooling axis for the core and cavity opening. Create the B surface for the given class A surface. Create the C surface with the help of class A and class…

                                                                                DRAFT ANALYSIS ON SWITCH BEZEL   OBJECTIVE:…

                                                                              DRAFT ANALYSIS ON SWITCH BEZEL   OBJECTIVE:…

                                                                                   BASE BRACKET DRAFT ANALYSIS…

                                                                                    DRAFT ANALYSIS ON FAN…