Project - 2 - Meshing on the suspension Assembly

 Frontal Crash Simulation Challenge aim To Check the unit system and either follow[Mg mm s] or [Kg mm ms]. Create an appropriate interface, friction 0.2 and recommended parameters. Make sure of no penetrations and intersections. Correct rigid bodies if any issues. Create a rigid wall with friction 0.1. Compare the model…

                            Side Pole Crash Simulation Challenge AIM Check unit system and either follow [Mg mm s] or [Kg mm ms]. Create appropriate interface ,friction 0.2 and recommended parameters. Make sure of no penetration and intersections. Create…

      AIM   Create the mesh for bumper assembly,mesh size should be 6mm.  Run the crash tube model as it is. Change the Inacti=6 and run. Create the type 11 contact and run. Remove both notches and remove boundary condition on rigid body node then run. Create a new notch in the middle,select the whole section and run Create…

AIM: To run crash analysis on the given model by applying different materials laws available in Radioss and post-process the results Objective: To carry out simulations of the given starter files and compare the results. There shall be 7 cases (according to given parameters) and they are to be compared primarily via animations…

OBJECTIVE To Comparison of results with base simulation and improved shell element properties under the given criteria by  CASE 1-Run the base simulation without any modification to element properties. CASE 2-Run the base simulation with element properties. PROCEDURE CASE 1 First, create a new folder on the desktop.IN…

1. Check the material properties of the rail component and calculate the speed of sound in steel raiL c = √ ( 21000/0.0078) c= 5188.74 ms. 2. The length of the rail is about 1000 mm. calculate the time takes for a shock wave to travel from one end of the rail to the other. Time taken, △T =>…

OBJECTIVES : To follow the mentioned quality criteria, mesh the Practice, Clip repair, Mounting Bracket component given below, and assign thickness. PROCEDURE : The given component is a STEP format file. Challenge has 3 different components as Practice, Clip repair, Mounting Bracket mesh one by one. The first mid surface…

AIM    To mesh the given Rear wheel component and give connections under the given quality criteria. PROCEDURE Import the given component in the ANSA. First, use the topo to fix all the free edges. And use check the geometry. If there is any error use the fix option to fix the issues…

AIM   To extract the midsurface and mesh the given plastic IP component under the given quality criteria. PROCEDURE The given component is import in ANSA.  Change the DRAW MODE to ENT. Seperate the Plastic component by using store lock in look panel. And take one component and start the process. First geomentry clenanup is…

AIM      To create basic morphing techniques for the given components. PROCEDURE First, the component is imported into ANSA. The component that will be morphed is shown in image below. To perform morphing actions, switch to Morph module. There are lot of tools to perform any given task. For box…

AIM    To perform the suitable connections for the given door component. PROCEDURE First import the given component in ANSA. The mesh is already present in the component.We want to Perform connections to the component. First seperate the component and given the different PID to it by using…

Total time taken-4hr

AIM     To mesh the given component using 2D tetra elements and define volume under the given quality criteria. PROCEDURE Import  the given component in the ANSA. First use the topo to fix all the free edges. And use check the geomentry.If there is any error use fix option to fix the issues or manually clean the issue.…

Total time to complete this two component is 12hr

AIM     To extract the midsurface and mesh the given plastic component under the given quality criteria. PROCEDURE The given component is import in ANSA.  Change the DRAW MODE to ENT. Seperate the Plastic component by using store lock in look panel. And take one component and start the…

AIM     To extract the midsurface and mesh the given hood component under the given quality criteria. PROCEDURE The given component is import in ANSA.  Change the DRAW MODE to ENT. Seperate the HOOD component by using store lock in look panel. And take one component and start the process. First geomentry…

AIM       To mesh the given component under mentioned quality criteria and assign thickness to it. PROCEDURE The given component is imported as .stp file format and the component is viewed by topo mode. The given component is checked for the uniformity in its thickness all over the geometry using distance…

AIM      To mesh the given plastic component under given quality criteria and assign thickness for it. PROCEDURE The given component is imported as .stp file format and the component is viewed by topo mode. Create line for split components by using node to node or node to line option in quick edite panel.…

AIM       To mesh the geomentry and create conector under given quality criteria. PROCEDURE  The given component is import as model formate. The component is viewed by topo mode. the geometry cleanup is carried out by manual cleanupmethod using the toggle option in quick edit Using the automesh option in the 2D panel,…

AIM      To create a Tetramesh for 3 different components with the given quality criteria. PROCEDURE 1.HOUSING The given component is imported as .stp file format and the component is viewed by topo mode. The given component is checked for the uniformity in its thickness all over the geometry usingdistance…

OBJECTIVES : To follow the mentioned quality criteria, mesh the hood component given below and assign thickness. PROCEDURE : The given component is STEP format file. In this file has 5 different components such as Outer extract, inner extract, 2 hinge reinforcement and a latch reinforcement of a hood. First mid surface…

AIM     To mesh the given component and to create 1D elements with the provided cross-sections and DOFs on the given component.  PROCEDURE Initially the given component is imported in IGES formate. midsurface is extracted in both the brackets by using the midsurface option in Geometry. Solid…

                                                          Design of American Chopper using Solidworks          Introduction This report contains a detailed…

                                                                              Sunseeker Yacht Design and Modelling using SOLIDWORKS…