DESIGN AND DEVELOPMENT OF CAR ROOF AND ITS REINFORCEMENTS Objective: The main objective of this project is to develop the car roof design and its reinforcements from the given styling surface. And to prepare a detailed report about the engineering standards for roof design, its design procedure, analysis and…
Jangaiah Chikonda
updated on 28 Jan 2024
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by Jangaiah Chikonda (22)
Project
AIM: In this project created motor blower assembly individual parts as per given dimensions an assembled together by considering appropriate constraints in CATIA V5.finally applied the Geometrical tolerances and Dimensions on the Motor blower . Introduction: The motor blower assembly consists of 6 parts,those are as below;…
20 Mar 2024 02:37 PM IST
Week 10 - Challenge 2- Attachment Feature Creation (Dog House)
28 Jan 2024 01:54 PM IST
Hood design-Week 2
28 Jan 2024 01:53 PM IST
Week 10 - Challenge 3 - Door Trim Lower with Engineering Features
28 Jan 2024 01:53 PM IST
Week 9 - Challenge 3 - Bumper
28 Jan 2024 01:53 PM IST
Week 11 - Project - A pillar Design with Master Section
28 Jan 2024 01:53 PM IST
Week 10 - Challenge 1- Attachment Feature Creation (Ribs & Screw Boss)
28 Jan 2024 01:52 PM IST
Week 9 - Challenge 1 - Base Bracket Design
28 Jan 2024 01:49 PM IST
Week 7 Challenge - Assembly Workbench
1.Create the CV joint and Quick Return Mechanism parts: 2.Use the Part Design workbench to create each individual part of the CV joint and Quick Return Mechanism. You can use various sketching and feature creation tools provided by CATIA V5 to design these parts. 3.Design each part based on the required dimensions, tolerances,…
28 Jan 2024 01:46 PM IST
Roof Design
DESIGN AND DEVELOPMENT OF CAR ROOF AND ITS REINFORCEMENTS Objective: The main objective of this project is to develop the car roof design and its reinforcements from the given styling surface. And to prepare a detailed report about the engineering standards for roof design, its design procedure, analysis and…
28 Jan 2024 01:41 PM IST
Week 12- Final project
28 Jan 2024 01:39 PM IST
Project 1
AIM: Route the wiring harness on the given engine and prepare the flattened view drawing in CATIA V5.application of all packaging rules, industry best practice studied in this course shall be demonstrated in design. Apply protection covering as required. ENGINE HARNESS INTRODUCTION: An engine wiring harness is a…
17 Jan 2024 03:53 AM IST
Project 2
AIM: Route the Wiring harness on Given car body and prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available connector 3D data can be used, or you can download the…
14 Jan 2024 08:41 AM IST
Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge
AIM: Flatten the harness assembly completed in “week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective covering has different visuals on drawing. Objectives: · To flatten the harness assembly created in the challenge week-4 · …
08 Jan 2024 03:50 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge
Aim: 1.route the two electrical harnesses as per the given layout and interconnect them as a single harness assembly. 2.check for bundle continuity, and the bundle warnings, and then provided annotations for the final harness assembly. Given master section: …
02 Jan 2024 04:38 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge
AIM: Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end) Download connector…
01 Jan 2024 12:36 PM IST
Wiring harness routing & packaging Rules Week 3 Challenge
WIRING HARNESS ROUTING AND PACKAGING RULES AIM: The main aim of this challenge is to understand the different types of clips& clamps, backshells and corrugated tube, defining it as an electrical component from available 3D cad files by using the electrical work bench in the CATIA V5 and creating the different corrugated…
28 Dec 2023 06:18 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge
WIRING HARNESS DESIGN IN CATIA V5-3D MODELING AIM: The given connectors and connector clips has to define as a electric component to used in harness routing process by defining its geometrical properties and other electrical construction definitions in electrical part design and assemble the connector and mounting…
25 Dec 2023 01:32 PM IST
Design of backdoor
BACK DOOR DESIGN OF CAR: Aim: To design the complete back door by using the given styling surface of back door by appropriate methodology and providing the necessary reinforcements, emboss, hinges by using the NX CAD. INTRODUCTION: BACK DOOR: Back door is the component which is situated the back side of the car, it is…
25 Dec 2023 01:01 PM IST
Fender Design
27 Nov 2023 01:45 PM IST
Section Modulus calculation and optimization
https://drive.google.com/file/d/1CiZbtGCHwJoRHe1fblEqgpvVF3rPQYQm/view?usp=drive_link NOTE:THE RESPECTED CHALLENGE FILES ARE UPLOADED IN THE ABOVE MENTIONED LIMK.PLEASE FOLLOW IT. THANK YOU
27 Nov 2023 12:48 PM IST
Week 9 - Challenge 2 - Switch Bezel Design
10 Oct 2023 02:19 PM IST