To Design RC column and beam for RC residential structure using TSD

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class AIM:- To export the Revit architecture and structure model to Navisworks Cache file following the export settings…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. AIM:- To create a set of sinusoidal points and create a curve and create a surface out of the curve using Dynamo. INTRODUCTION:- Manage tab provides access to Dynamo which is an open source visual programming…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School Over here I decide to choose Multi-Unit Residential Apartment.   2) Assume reasonable…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level AIM:- To Model a Ceiling from the architecture tab above the walls at the first-floor level from week 3 project. INTRODUCTION:- Ceilings are created above each…

AIM:- To develop general arrangement for the RC office building. Also, to analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER from the attachment. Also, to generate report of each member and extract drawings for structural plans, beam reinforcement details from the software. INTRODUCTION:-…

Generate report for the steel building design from challenges 1 – 6 along with the loading summary AIM:- To generate report for the steel building design from challenges 1 – 6 along with the loading summary INTRODUCTION:-  Report generation helps us to get detailed report for each members and completed…

Design the slab and foundation of the model. Outline the thought process for designing of the elements (column, beam, slab and foundations)  AIM:- To design the slabs and foundation for the model.  INTRODUCTION:- Slab design are done based on the dead load, live load and floor finishes and based on this slab…

Based on the analysis design RC column and beam. AIM:- To design RC column and beam based on the analysis. INTRODUCTION:- Design of beam and column includes selection of member size, reinforcement required, grade of concrete etc. so as to transfer the load safely. Design is checked based on analysis preformed on strength…

Generate seismic loading based IS codal provisions and zone II. Any other data you can assume and input accordingly AIM:- To generate seismic loading based IS codal provisions and zone II. Any other data you can assume and input accordingly INTRODUCTION:- Seismic load are the earthquake load on the structure which acts…

Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab thickness as per the design Brick wall load Roofing load AIM:- To calculate dead load in design report based on IS code and to apply dead load on the model INTRODUCTION:- Dead load are normally the weight of th…

1. Setup model for RC building design and based on following parameters for cover MEMBERS IN CONTACT WITH GROUND ABOVE GROUND Column 50mm 40mm Beam 30mm 25mm Slab 30mm 25mm Pilecap 75mm   Foundation 50mm   AIM:- To setup model for RC building design and based on the cover parameters INTRODUCTION:- Setting must…

Analyze and design a steel building to 10T CRANE as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. Provide bracings and moment connection for lateral stability.  Consider dead, live, equipment and wind loading. Consider the brick wall loading for 150mm thick and 1.5 KN per…

Summarize your study for the bending moment, shear force and deflection diagrams for the elements of the model AIM:- To summarize your study for the bending moment, shear force and deflection diagrams for the elements of the model INTRODUCTION:- Bending moment, shear force and deflection diagrams are analytical diagrams…

Generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39m/s Terrain category 2 AIM:- To generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39m/s Terrain category 2 INTRODUCTION:-The wind load which acts on…

Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab as per design Brickwall 150mm thickness Roofing load based on purlin size Ceiling loading 0f 0.3KN per sq m AIM:- To calculate dead load in design report based on IS code and apply dead load on the model:- Finishes…

Create beam properties for First floor and model the beams AIM:- To create beam properties for First floor and model the beams INTRODUCTION:- Beam are provided to carry slab loads of that particular floor, ie, beams in the first floor takes the slab load that is placed above it. Tekla Structural Design is used to…

Create column properties for different types of pedestal members and model in the grids created as per the assignment 1 AIM:- To create column properties for different types of pedestal members and model in the grids created as per the assignment 1. INTRODUCTION:- Tekla Structural Design is used for modelling, analysis…

 Summarize the user interface in TSD AIM:-Summarize the user interface in TSD with the for the following items:-  Project Workspace Scene Content Create Two scene views Loading drop list Properties window INTRODUCTION:- User interface in TEKLA STRUCTURAL DESIGN consist of:- Quick Access Toolbal which…