To Design slab and foundation for an RC residential building using TSD

Aim :-            Conduct the post-processing of the results once the analysis is complete. The first task includes checking the base pressure and settlement beneath the base slab which should be within the limits mentioned in Project-1. If these limits are exceeded then the dimensions need…

A residential society has 200 x 2BHK flats and 100 x 3BHK flats. A typical family in a 2BHK flat has 3 persons/flat and a 3BHK flat has 4 persons/flat. The gross water demand (per person per day in liters) can be calculated by taking the aggregate of the usage for all the below listed activities. Activities Consumption…

A 30 - 40hr project on modelling, analysis & design of a state-of-the-art tall composite building using ETABS software. The composite members to be designed using Comflor software. Key Highlights: a. Modelling The structural model prepared for the project 1to be used for the project 2. Prepare two distinct structural…

A 30 - 40hr project on modelling, analysis & design of a state-of-the-art tall building using ETABS software. Key Highlights: a. Modelling To comprehend the architectural plan provided by the architect and look-out for the key information from the drawings. Import the architectural floor plan (provided by the architect)…

1) The design of reinforced concrete (RC) column is carried out by following certain procedures. However, some specific rules and requirements need to be met. The conditions are commonly related to reinforcement ratio, size of rebars, spacing of steel bars, size and spacing of lateral ties or spirals, thickness of concrete…

AIM:- To develop general arrangement for the RC office building. Also, to analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER from the attachment. Also, to generate report of each member and extract drawings for structural plans, beam reinforcement details from the software. INTRODUCTION:- Tekla…

  AIM:- to generate the  report  for the steel  building design Procedure:- Open the Tekla model Now go to report option from the ribbon and select model report Now select the load cases and combinations summary to obtain report Click on the show report to obtain report We can change the project name , address etc with …

Aim:- to design slab panels of the RC model Procedure:- open the tekla RC model with all the structural elements added and analysed now select all the slab elements right click on the slab panel to view the design options now select on the check panel option if it shows that no valid loadcombinations are found then we…

1) ANS:- AIM:- To generate seismic loading based on Is codal provision and zone 2. Any other data you can assume and input accordingly. TOOLS USED:- Load. Loadcases. seismic wizard. Seismic load. Analyze. PROCEDURE:- First we have to open the previous week challenge in the TEKLA software. After open the file now click…

Q1 ) Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab thickness as per the design Brick wall load Roofing load ANS 1) AIM : To calculate the dead load based on the design and apply it on the structure. TOOLS USED : MS Excel. Loads. Loadcases. Dead load. Area.…

1. Setup model for RC building design and based on following parameters for cover MEMBERS IN CONTACT WITH GROUND ABOVE GROUND Column 50mm 40mm Beam 30mm 25mm Slab 30mm 25mm Pilecap 75mm   Foundation 50mm     AIM: To set up model  for RC building design based on the parameters for cover MEMBERS IN CONTACT WITH GROUND ABOVE…

Analyze and design a steel building to 10T CRANE as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. Provide bracings and moment connection for lateral stability.  Consider dead, live, equipment and wind loading. Consider the brick wall loading for 150mm thick and 1.5 KN per sq…

1. Summarize your study for the bending moment, shear force and deflection diagrams for the elements of the            model Bending Moment : Bending moment (BM) is a measure of the bending effect that can occur when an external force (or moment) is applied to a structural element. This concept is important in structural…

1.Generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39m/s Terrain category 2 Ans) Aim:To generate manual wind loading in the design report based IS code as per the following input which are mentioned in the question. Tools Required: -> Tekla model -> Dimensions…

1. Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab as per design Brickwall 150mm thickness Roofing load based on purlin size Ceiling loading 0f 0.3KN per sq m AIM : To calculate dead load in design report based on IS code and apply dead load on the model TOOLS…

1.Create beam properties for First floor and model the beams.Ans)Aim: To create beam properties for First floor and model the beams.Tools Required:-> Levels-> Manage Properties -> New -> Members -> Steel Beam.-> Grids-> Beams-> Properties tab.-> ValidateProcedure:• Firstly open the software and change the settings.• Now…

AIM: To create column properties for different types of pedestal members and model in the grids created as per the assignment 1 Introduction: The pedestal is the block of concrete that supports the column. It transfers the load from the column to the foundation safely. It is also provided to avoid contact between the soil…

1 ans: Project Workspace – How to access and usage in Tekla: First, open the Tekla software Next click on the New option, then the project workspace will be visible as shown below   Scene Content – Demonstrate the use of scene content: Now click on the scene content option at the left side of the screen as shown below…

Aim - i) To  model the isolated footing provided in week 11 challenge on SAFE.          ii) To Analyze and design it to verify the size, depth and steel provided as per calculations.          iii) To model the pile cap on SAFE software .     Introduction -    1) CSI SAFE (Slab Analysis by the Finite Element Method) is…

AIM: To design a square footing for a column size of 400x400 for given constrains and do the following check: If the gross bearing pressure under the footing is within safe bearing capacity Provide sufficient depth and longitudinal steel for resisting bending and shear Sufficient anchorage for column steel into the footing…

QUESTION:- The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been…

Aim:   To run the analysis and design the RCC shear walls shown in the etabs model. Step 1: 1) Open the ETABS file 2) After the analysis click Concrete frame design Step 2: 1) Need to check there is any failures occurs 2) Click Shear wall design tool 3) select Display info and choose PM failure  Step 3: 1) Click any wall…

Aim: To Providing details of longitudinal reinforcement for the two columns from foundation to terrace level. Step 1: 1) Open a G+4 Etab file 2) Click the Concrete Frame Design tool 3) Select the Display Design Info option 4) Choose design output as Longitudinal Reinforcement Step 2: 1) After Selecting the Longitudinal…

Reinforcement Detailing of Beams from ETABS output   QUESTION:- Detail design of beams in Etabs 2018.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous…

Aim: to model and analyse a 25 storey building with given specifications and to cross check the parameters as per IS 1893 provisions. Procedure: Open the ETABS software. Click the file menu and choose to create a new model option. After choosing a new model a dialogue box will appear as model intialization. Choose the…

1. The building shown, 20 x 30m in plan, has column on a 5 x 5m grid and shear walls( with dimensions shown in m, 250mm in thickness) in three alternative arrangements. (a, b, c), all with the same cross sectional area of the shear wall. Compare the three alternatives, taking into account the restraint of floor shrinkage,…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility.   Answer: 1.Symmertry Having a look over the aspects of symmetry of…

Aim: To compute the values of seismic parameters based on the given structural data Step-1 Step-2: Step-3 Step-4 Step-5

Que :- 1. Differentiate Static analysis and Dynamic analysis with proper representing pictures (30 marks) AIM:- To Differentiate Between Static analysis and Dynamic analysis Ans:-    Static Analysis:-  In Static analysis we analysis static load means “a force that has constant size, position and direction on or within…

) What is the mode of failure or damage of the beams in the figure above? Would you characterize the case as damage or as a failure? Are the damages repairable? Elaborate. a)              This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus of rupture, bend strength,…

AIM: To design and analysis of G+3 (RCC) hostel building in ETABS and Foundation in CSI SAFE. INTRODUCTION: The procedure and anaylsis and design of given building will depend on the type of building, its complexity, the number of stories etc.First architectural drawings of the building are studied, structurl systems is…

AIM:         TO MODEL AND ANALYZE MULTIPLE BUILDINGS WITH DIFFERENT FLOOR LEVELS AND DESIGN PARAMETERS USING ETABS SOFTWARE AND COMPARE THE RESULTS TO UNDERSTAND THEIR OVERALL SEISMIC BEHAVIOUR. INTRODUCTION:              The structural configuration of the building plays a major role in determining the overall response…

1.Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows: Width  30m Length 50m Eave Height 9m Bay spacing 6m Soil type Medium Safe Bearing Capacity 200 kN/m2 Roof slope 1 in 12 Assume suitable sections for structural elements. Follow IS800:2007, IS1893…

Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows:      Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180 kN/m2…

1.1 State the primary load cases to be considered for design. Answer. The primary load cases that are to be considered for design are listed below: Dead Load (IS 875: Part I). Live Load (IS 875: Part II). Wind Load (IS 875: Part III). Snow Load (IS 875: Part IV). Seismic Load (IS 1893: 2016). 2.…

  1. How will you assign Circular section to column? Step1:-  First open the STAAd.Pro software by double clicking on it Then click on New then the model information tab opens  Add the details into it and click on create     Step2:-  After creating a model then create a node in the geometry tab Give the 1st node co-ordinates…

1. Write the steps involved to upload a .std file through web mail? ANSWER Steps involved to upload a .std file through web mails are as follows; Open the STAAD pro software and locate the share option available on the introduction screen. After clicking on the share button, select send mail option. Then, browse for the.…

Aim: Aim is to sketch a G+1 floor residential plan according to Vaastu Shastra and list down the structural drawings required to be provided to the site construction. Introduction:   Vasthu Shastra is the ancient Indian science of architecture and acts as a guideline to design your home in a way that enhances…

Project on : Concrete Mix Design for various grades of concrete   Aim: concrete mix design for M35 grade concrete with fly ash Objective:  To make a concrete mix workable for the different structural members of building  by selecting proper proportion of concrete ingredients, through this selection…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class Aim: To Exporting the Revit architecture and structure model to the Navisworks Cache file as discussed in the…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve.   AIM: To create a set of sinusoidal points and create a curve and create a surface out of the curve using Dynamo .  PROCEDURE : step 1: Open revit > architectural template >manage tab . …

1) Select the type of structure you want to build from one of the three below a. Multi-Unit Residential Apartment b. Office Buildings c. school ans) I chose Office Building __________________________________________________________________________________________________________________________________________________________…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level Aim: To model a Ceiling from the architecture tab above the walls at the first-floor level Procedure: Step 1: From the architectural tab, ceiling tab is used…

.AIM:To create a 3D redered model for a residential building in AutoCAD PROCEDURE: First open the Autocad and click on settings below and in that select 3D modelling. After selecting the 3D modeling set the units and limits as per the drawing requirements. After that go to views and select top view and draw the drawing…

1.AIM:To creeat a 3D isometric view of the building with plan and elevation by using Autocad 3D modelling. PROCEDURE: First open the Autocad and click on settings below and in that select 3D modelling. After selecting the 3D modeling set the units and limits as per the drawing requirements. After that go to views and select…

Drawing1:     Aim: To draw the given 3D object(Furniture element) in 3D basics. Introduction: The Object is drawn as per the given dimension and to have the multiple views in 3D. Procedure: The object assesment is done to create all the views possible. Drawing of the element is started once the UCS is made ready…

Drawing1:   Aim: To Create a layout of the Floor Plan and Section A of the Building and to take a plot. Introduction: The given drawings are coverted into PDF and printed for making the Drawing sheets Using the template TutorialmArch.dwt Procedure: The Drawings after created in Autocad are converted into PDF using…

1) Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks whereverrequired. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and othersas per the standards. Aim: To Create the Kitchen Layout and to  Also, use proper dimension techniques to dimension…

1. AIM:         To create the templates as shown in figure, add texts, attributes and save the templates as blocks with names custom titleblock 1 and custom titleblock 2. Explain the procedure step by step and show the result. INTRODUCTION:         AutoCAD is a computer…

AIM:- To create an own Architectural drawing consisting of Floor plan, Elevations and Sections for the plot size 60'x20' and also create the structural drawings for Column, Footing and Beam. INTRODUCTION:- The Architectural and Structural drawings are sketched up in AutoCAD using various tools / commands. The given details…