To Generate report for Steel Industrial and RC structures using TSD

Question. A 30 - 40hr project on modelling, analysis & design of a state-of-the-art tall building using ETABS software.Key Highlights:a. Modelling:To comprehend the architectural plan provided by the architect and look-out for the key information from the drawings.Import the architectural floor plan (provided…

Aim:To analyse and to design the composite high rise building using ETABS. And to design the composite deck profile using Comflor software. Procedure:Following  for composite and design:Architectural plan study & Column shear wall position markingSteel beam alignment marking (considering approximate deck…

Aim: To model and analyse a 25 storey building with given specifications and to cross check the parameters as per IS 1893 provisions. Procedure: Open the ETABS software. Click the file menu and choose to create a new model option. After choosing a new model a dialogue box will appear as model intialization. Choose the…

  Develop general arrangement for the RC office building. Analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. The building to be designed for dead, live, wind and seismic loading. Report of each member to be generated and extract drawings for structural…

    1-AIM:- to generate the  report  for the steel  building design Procedure:- Open the Tekla model Now go to report option from the ribbon and select model report Now select the load cases and combinations summary to obtain report Click on the show report to obtain report   We can change the project name , address etc…

1.Design the slab and foundation of the model. Outline the thought process for designing of the elements (column, beam, slab and foundations) Aim - To design the slab and foundation of the model.   Tools Used - 1st Order analysis, Analysis all ( static ), Status , check panel ,Properties window etc.   Procedure - Open…

1.) Based on the analysis design RC column and beam. AIM :    To Based on the analysis design RC column and beam.   INTRODUCTION :  An ordinary reinforced concrete beam or the column itself is an inhomogeneous section composed of concrete and reinforcement, whose behavior is totally different. A reinforced concrete column…

1. Aim: To generate seismic loading based IS codal provisions and zone II. Procedure: Open the previously save Tekla model Now go to the load cases and add the seismic load case, and click ok Now go to the seismic wizard and select code specta and click Next. Now enter the zone and click Next Now we have to enter the structure…

1. Setup model for RC building design and based on following parameters for cover MEMBERS IN CONTACT WITH GROUND  ABOVE GROUND Column 50mm  40mm Beam 30mm  25mm Slab 30mm  25mm Pilecap 75mm   Foundation 50mm   AIM :    To Setup model for RC building design and based on following parameters for cover   INTRODUCTION :   …

1. Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab thickness as per the design Brick wall load Roofing load   Aim - To calculate dead load in design based on IS Code and apply on model. Tools Used - Load Cases, Full Udl , Area Load, Property Window. Calculation…

Analyze and design a steel building to 10T CRANE as per IS standard code using TEKLA STRUCTURAL DESIGNER.   AIM: To analyze and design a steel building to 10T CRANE as per IS standard code using TEKLA STRUCTURAL DESIGNER. INTRODUCTION: Tekla Structural Designer is an integrated model-based 3D tool for analysis and design…

1. AIM: Summarize your study for the bending moment, shear force and deflection diagrams for the elements of the model PROCEDURE:  Initally open the Tekla file you saved prviously After opening the file->We ste the Seismic data in the structure To set->go to Load panel->Under seismic load go to Seismic wizard Select the…

1) Aim - Generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39 m/s Terrain category = 2 Procedure - First calculate load combination  Result - Calculations are done for the wall panel   2) Aim - Based on the above calculation apply the loading on the model Procedure…

1. AIM: Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab as per design Brickwall 150mm thickness Roofing load based on purlin size Ceiling loading 0f 0.3KN per sq m PROCEDURE: Dead load calculations of the the structure as per the structures is given below Dead…

. AIm: To Create beam properties for the First floor and model the beams. Procedure: Open the Tekla structure software  And then open the week2 challenge file. Now go to levels and select intermediate floor Now go to manage property and create the new beam  And then model the beam. Now Model the secondary beams in the…

  1.AIM: To create column properties for different types of pedestal members and model in the grids created as per the assignment 1 Introduction: The pedestal is the block of concrete that supports the column. It transfers the load from the column to the foundation safely. It is also provided to avoid contact between the…

1)Summarize the user interface in TSD with the for the following items: -    Project Workspace – How to access and usage   Scene Content – Demonstrate the use of scene content   Create two scene views   Loading drop list- How to access   Properties windows – how to access and usage Aim - To summarize the user interface…

Project 2. Ans -  Files and snaps are attached below. Aim - To Model & Design a Proposed PEB Warehouse using STAAD. Pro. Introduction - Here we model and design the PEB warehouse building. As per given description, material data, specification we can design it.  PEB - Pre engineered buildings are factory built buildings…

1. Design a multi-story Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows: Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180 kN/m2 Maximum slab thickness 150mm…

1. State the primary load cases to be considered for design. ANSWER: The primary load cases that are to be considered for design are listed below: Dead Load (IS 875: Part I). Live Load (IS 875: Part II). Wind Load (IS 875: Part III). Snow Load (IS 875: Part IV). Seismic Load (IS 1893: 2016). 2. What…

1. 1. How will you assign Circular section to column? AIM: To assign Circular section to column INTRODUCTION: Columns are defined as vertical load-bearing members supporting axial compressive loads chiefly. This structural member is used to transmit the load of the structure to the foundation. In reinforced concrete buildings…

1. a) AIM : Write the steps involved to upload a .std file through web mail? Introduction :  STAAD pro ( Structural Analysis and Deign program is the abbrivation for the STAAD it is the connected version new version used to analize the RCC structure and steel structure by using this software ) It Include…

AIM:-To Create and Analyse the given building in ETABS 2018, the structural model has to be prepared in accordance with IS 1893 and as per IS 13920. To design the pile cap and pile reinforcement details,Tie  beam  connecting the pile caps, to sketch the column reinforcements, to produce the framing plan and beam detailing…

QUESTION:1 Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. ANS: AIM: To Analyze and designthe isolated footing from week 11 challenge on SAFE To verify the size, depth and steel provided as per calculations.  …

  QUESTION:- Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either a tapered or stepped footing. Besides the total…

  QUESTION:- The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have…

Aim:   To run the analysis and design the RCC shear walls shown in the etabs model. Step 1: 1) Open the ETABS file 2) After the analysis click Concrete frame design Step 2: 1) Need to check there is any failures occurs 2) Click Shear wall design tool 3) select Display info and choose PM failure  Step 3: 1) Click any wall…

Note: Load Combination 68 to Load combination 79 has 0.9Dead +0.9 Brickwall + 0.9 floor finish  Load Combination 73,75,77,79 has positive axial load at the bottom for the column 3F. Therefore Column 3F is subjected to Tension for the above load combinations.   Question: Reinforcement detailing of columns in Etabs 2018.…

Reinforcement Detailing of Beams  QUESTION:- The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous beam along grid A        2) 7 span continuous beam along…

                                            Comparative Study of Different Story Buildings for Seismic Forces   AIM: TO MODEL AND ANALYZE MULTIPLE BUILDINGS WITH DIFFERENT FLOOR LEVELS AND DESIGN PARAMETERS USING ETABS SOFTWARE AND COMPARE THE RESULTS TO UNDERSTAND THEIR OVERALL SEISMIC BEHAVIOUR. INTRODUCTION:        …

Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account…

AIM:- To undersstand the  Concept on positioning of Columns INTRODUCTION:- There are some of the basic principles in determining the positions of columns. Some of them are: Columns should be preferred to be positioned at the corners of the building and at the intersection of beams. They should be placed in such…

Aim: To compute the values of seismic parameters based on the given structural data Step-1 Step-2: Step-3 Step-4 Step-5 Ln, Mn, Tn values are calculated for each of the 5 modes The base shear force for each of the 5 modes is obtained. Effective modal mass and the modal mass participating ratio for 5 modes are obtained…

1. Differentiate Static analysis and Dynamic analysis with proper representing pictures . The nature of loading governs the kind of analysis to be performed on the structure. The loads are divided into two basic categories Static Loads are the loads, the variation of load with respective time is very slowly (the acceleration…

1) What is the mode of failure or damage of the beams in the figure above? Would you characterize the case as damage or as a failure? Are the damages repairable? Elaborate. a)              This crack will be formed due to the flexural failure of a beam. The flexural strength, known…

1:) Aim:- Exporting the Revit architecture and structure model to Navisworks Cache file following the export settings. Tools used:- Revit, Projects, Export option, file menu, 3D view etc. Navisworks is Used primarily in construction industries to complement 3D design packages (such as Autodesk Revit, AutoCAD), Navisworks…

Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo Introduction: Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. Its a programminglanguage that allows you to type lines of code; while also creating…

Creating Architectural and Structural model with 3D rendering using REVIT Introduction Revit enables the project to be completed in a combined effort. Structural engineers that are using Revit and are working with architects using Revit Architecture can directly link to the architectural model. Linking a revit architectural…

  1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level.     AIM:- To model a Ceiling from the architecture tab above the walls at the first-floor level.     INTRODUCTION:-…

AIM:  To create a 3D rendered model for a Residential Building in AutoCAD INTRODUCTION: The main objective of this project is to understand about to create a Plan in 2D, then convert it into 3D using AutoCAD 3D, applying materials and rendering. AutoCAD is primarily used for generating 2D sketches. While it is possible…

CHALLENGE:-1 Q] Create a 3D Isometric View of the building with plan and elevation given.        AIM:- To create a 3D isometric view of the given building with plan and elevation.    INTRODUCTION:-  An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface. One of the defining characteristics…

AIM: To create 3D model and view of: Furniture element Isolated footing AASTHO type girder Drop column with panel A wall Commands used: Extrude. Offset. UCS. Box. Union. Subtract. Move. 3d orbit. Loft. Sweep. Cone. Region. Boundary. PROCEDURE:  Open the AutoCAD, click on workspace switching and change it to 3d modelling…

1) Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size forthe layout.…

Aim:         To Create the Kitchen Layout and to  Also, use proper dimension techniques to dimension the kitchen               layout. Also, insert text wherever required. All dimensions are in mm.       Procedure: step 1: units are set to mm limits and limax are also set  zoom comand is also used  Step 2: In the command…

AIM:To Create Custom1_titleblock and Custom2_titleblock using Attributes and block command from Autocad software .PROCEDURE:Step 1 ( custom1_tittleblock)In the command prompt type L to draw the lines In ribbon tab > Annotate > Mtline ( to draft the text )go to properties tab to change the colour  In the riibon bar >block…

Project 1- Submitted by Md Sameer  Commands Used in this challengeLineXlinePolylineRectangleCircleArcTrimMoveOffsetHatchLayerMatchPropMultileaderFilletCopyExplodeDimlinearDimcontinueDim breakDim updateHide pallets (POFF)Show pallets (PON)Q. Design and Draft a layout of a residential building with the following details:Plot…

Aim:- To draw the floor plans and sections using the proper dimension techniques and dimension styles to document the project.    Introduction:-Plan and Sections are different types of drawings used by architects to graphically represent a building design and construction.A plan drawing is a drawing on a horizontal plane…

AIM:To draw the elevation and details of a wardrobe as shown in the figure. After sketching, you need to provide the dimensions and text with the use of layers. PROCEDURE:STEP 1:Units are set to mmLimits and limax are also setZoom command is also usedSTEP 2:In the command line type rec > 2800,2600In the command line type…

AIM :1. Create a column schedule as shown in the figure.Note: Create a column schedule with the help of lines. Also, insert text with the help of Dtext command or Single Line text. Hint: Use font name: romans.shx; Height: 8”, Justify: LeftSOFTAWARE USED : AUODESK AUTOCAD 2021 PROCEDURE :first the open the software give…

Aim:To draw the layout of a residence plan.Commands used:XL-V OR XL-H.Offset.Fillet.Extend.Trim.Procedure:First create a new AutoCAD file with imperial settings.Make sure that in units the type is "Engineering" (as the dimension is in feet and inches) and also set the precision.Set the limits with command "LIMITS" specify…

Aim: To draw cross section of wall over footing.Commands used:Line.Rectangle.Trim.   Procedure:Step:1 - Create rectangle by typing "REC" in command box Specify the first corner point as (5,5)Specify the length of rectangle =0.9 units in command boxSpecify width of rectangle =0.25 units in command boxStep:2- Create another…

Cross section of load bearing wall over spread footing.Aim: To draw cross section of wall over footing.Commands used:Line.Rectangle.Trim.   Procedure:Step:1 - Create rectangle by typing "REC" in command box Specify the first corner point as (5,5)Specify the length of rectangle =0.9 units in command boxSpecify width of…

AIM:         (A) Create the geometries from P1 to P8 using all the coordinates system methods. And we need to use line tool, and find the missing dimensions.        (B) Civil related problems- Draw the profile and the trusses using any coordinate system methods. The dimensions…

AIM:sketching the G+1 floor residential plan satisfing the vaastu shastra and calulating the load acting on the building with giving the information of the required drawings.answer:Ground floorFirst floorOpening is provided above the ground level for the aesthetic lookAll doors are inwards Herei. Main door is facing the…

  AIM: To Calculate the Concrete Mix Design for M35 grade concrete with fly ash & M50 grade concrete without Fly ash INTRODUCTION:Concrete mix design is the method of finding the precise proportion of cement, sand and aggregates for concrete to achieve the target strength in structures, therefore concrete…