case 1: Max Total deformation=2.7492e-4 mm Max Equivalent stress=0.60542 Mpa case 2: Max Total deformation=2.9728e-4 mm Max Equivalent stress=0.5826 Mpa 1.From an analysis standpoint, i would select the model in case1, It provides less damage to the model, because the stress developed is slightly higher,deformation…
jeya soorya
updated on 20 Jul 2021
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by jeya soorya (26)
Week 1 Spur Gear Challenge
Values achieved from simulations: Result cast iron cast bronze cast steel Total deformation 30 mm 30 mm 30 mm equivalent elastic strain 3.3113e-03 3.6791e-03 1.5322e-03 equivalent stress 291.76 Mpa 290.25 Mpa 306.09 Mpa kindly, suggest to me on what basis, should I come up with a suitable material.
09 Aug 2021 02:01 PM IST
Week 1 Stress Concentration on a Plate with hole
case 1: Max Total deformation=2.7492e-4 mm Max Equivalent stress=0.60542 Mpa case 2: Max Total deformation=2.9728e-4 mm Max Equivalent stress=0.5826 Mpa 1.From an analysis standpoint, i would select the model in case1, It provides less damage to the model, because the stress developed is slightly higher,deformation…
20 Jul 2021 05:10 PM IST
Project - 2 - Meshing on the suspension Assembly
OBJECTIVE: The main aim of this project is to perform meshing on the given Cad model of the suspension system as per the quality criteria shown below and to provide necessary connections. QUALITY CRITERIA: For Surface Meshing of Tyre and Rim (Element type: Tria) : S.No Quality Criteria Value 1 Target/Average…
08 Apr 2021 06:16 PM IST
2D MESHING ON THE INSTRUMENTAL PANEL
OBJECTIVE: The main aim of this project is to mesh the half of the IP console model as per the quality criteria shown below and to assign thickness. QUALITY CRITERIA: S.No Quality Criteria Value 1 Target/Average length 4 2 Minimum Length 2 3 Maximum Length 6 4 Aspect …
11 Mar 2021 06:54 AM IST
BASIC MORPHING USING ANSA V20.1.4
OBJECTIVE: The main aim of this project is to perform the basic morphing technique for a Hand rest plastic component and a sheet metal component. PROCEDURE: Hand rest plastic component: Imported the given .stp file in the ANSA work page. Checked for the orientation i,e. the upper part of the model should be in gray color…
23 Feb 2021 03:49 PM IST
CROSS CAR BEAM ASSEMBLY USING ANSA V20.1.4
OBJECTIVE: The main aim of this project is, To mesh the cross-car beam parts as per the quality criteria shown below. To provide necessary connections. To assign thickness. QUALITY CRITERIA: S.No Quality Criteria Value 1 Target/Average length 5 2 Minimum Length 3 3 Maximum Length …
20 Feb 2021 05:17 PM IST
MESHING THE INTAKE MANIFOLD OF AN ENGINE USIGN TETRA ELEMENTS IN ANSA v20.1.4
OBJECTIVE: The main aim of this project is to mesh the Intake manifold of an engine using tetra elements as per the quality criteria shown below. QUALITY CRITERIA: S.No Quality Criteria Value 1 Target/Average length 3 2 Minimum Length 1 3 Maximum Length 5 4 Tetcolapse 0.2…
10 Feb 2021 10:20 PM IST
CREATING CONNECTION OF A REAR DOOR IN NASTRAN DECK
OBJECTIVE: The main aim of this project is to connect the FE model of the rear door of a car in Nastran deck for NVH domain. PRE-REQUISITES: NVH domain study about the natural frequency of the body at which it vibrates, so for the basic simulation mechanisms in the system are not need to be defined (case specific). Basically,…
10 Feb 2021 10:18 PM IST
MESHING THE SWITCH PANEL AND A SHEET METAL COMPONENT USING ANSA V 20.1.4
OBJECTIVE: The main aim of this project is to mesh the Switch panel of a car and a sheet metal component as per the quality criteria shown below and to assign thickness. QUALITY CRITERIA: S.No Quality Criteria Value 1 Target/Average length 4 2 Minimum Length 2 3 Maximum Length …
04 Feb 2021 03:03 PM IST
TETRA MESHING OF RERAVIEW MIRROR USING ANSA V 20.1.4
OBJECTIVE: The main aim of this project is to mesh the Rearview mirror using tetra elements as per the quality criteria shown below. QUALITY CRITERIA: S.No Quality Criteria Value 1 Target/Average length 1 2 Minimum Length 0.5 3 Maximum Length 2 4 Tetcolapse 0.2 PROCEDURE:…
04 Feb 2021 03:01 PM IST
MESHING A BOTTLE CAP USING ANSA V 20.1.4
OBJECTIVE: The main aim of this project is to mesh the Bottle cap as per the quality criteria shown below and to assign thickness. QUALITY CRITERIA: 1 Target/Average length 1 2 Minimum Length 0.5 3 Maximum Length 3 4 Aspect 3 5 Warpage 15 6 Skewness 45 7 Jacobian 0.7 8 Minimum Quad Angle …
28 Jan 2021 05:54 PM IST
MESHING A HOOD OF A CAR USING ANSA V20.1.4
OBJECTIVE: The main aim of this project is to mesh the hood of a car as per the quality criteria shown below and to assign thickness. QUALITY CRITERIA: S.No Quality Criteria Value 1 Target/Average length 5 2 Minimum Length 2 3 Maximum Length 7 4 Aspect 3 5 Warpage 15 6 Skewness…
23 Jan 2021 05:03 PM IST
ROOF CRUSH ANALYSIS OF DODGE NEON BIW AS PER THE FMVSS 216A STANDARD
OBJECTIVE: The main of this project is to perform the roof crush analysis of Dodge Neon BIW as per the requirements and procedures in FMVSS-216a standard published in 2009. FMVSS-216a STANDARD: FMVSS 216, Roof Crush Resistance, establishes strength requirements for the passenger compartment roof of passenger cars, multipurpose…
08 Jan 2021 11:40 AM IST
SIDE CRASH ANALYSIS OF NEON'S BIW USING HYPERCRASH AND RADIOSS
OBJECTIVE: The main aim of this project is to perform a side crash of neon's BIW model using preprocessors like Hypermesh, Hypercrash, and Radioss solver. PROCESS: 1. The consistent unit system in this project is Kg mm ms KN. 2. Created an appropriate contact interface type-7 self-impact with the recommended parameters…
29 Dec 2020 04:43 PM IST
FRONTAL CRASH ANALYSIS OF NEON'S BIW USING HYPERCRASH AND RADIOSS.
OBJECTIVE: The main aim of this project is to perform a frontal crash of neon's BIW model using preprocessors like Hypermesh, Hypercrash, and Radioss solver. PROCESS: 1. The consistent unit system in this project is Kg mm ms KN. 2. Created an appropriate contact interface type-7 self impact with the recommended parameters…
25 Dec 2020 03:20 PM IST
MESHING A HOOD OF A CAR USING HYPERMESH
objective: the main objective is to mesh the given component according to the quality criteria given in the question. Element quality criteria : S.N Quality Criteria Value 1 Target Element Length 5 2 Aspect Ratio 3 3 Skewness 45 4 Warping 30 5 Taper 0.5 6 Min. Length 3mm 7 Max.…
15 Dec 2020 04:34 PM IST
TETRA AND HEXA MESHING OF DIFFERENT COMPONENTS USING HYPERMESH.
1.Objective (tet mesh): The main objective of this project is to create a 3D tetra mesh for the component (housing) as per the quality criteria given below. Quality criteria: Elements sizes: Min- 2mm, Target- 5mm, Max- 7mm Tet collapse: 0.15 Procedure: Imported the file from the question and performed the 2d tria…
15 Dec 2020 06:10 AM IST
MESHING THE BACKDOOR GEOMETRIES OF DIFFERENT CARS USING HYPERMESH.
1.Objective: The main objective is to mesh the backdoor component according to the quality criteria given below. Target Element size - 5mm S.N Quality Criteria Value 1 Aspect Ratio 5 2 Skewness 45 3 Warping 15 4 Taper 0.5 5 Min. Length 4mm 6 Max. Length 7mm 7 Min angle Quad 45 8 Max…
15 Dec 2020 03:30 AM IST
CASE STUDY ABOUT TYPE2 , TYPE 7 AND TYPE 11 CONTACT INTERFACES AND THE INFLUENCE OF NOTCH IN THE CRUSH TUBE USING RADIOSS SOLVER.
OBJECTIVE: The main aim of this project is to study and compare the contact interface type 2, type 7, and type 11. To study how the notch influence the simulation in the crush tube model. To mesh the bumper assembly model with a 6mm element size. BUMPER MESHING: procedure followed: imported the given model (.hm) file…
26 Nov 2020 02:27 PM IST
CASE STUDY ABOUT LAW 1,LAW 2, LAW 27 AND LAW 36 MATERIAL CARDS WITH DIFFERENT PARAMETERS USING RADIOSS SOLVER IN HYPERMESH.
OBJECTIVE: The main aim of this project is to analyze the different material card cases given and to derive the case which represents the on-field scenario. DESCRIPTION: case1: imported the given failure_johnson_0.rad file in the hypermesh GUI. simulation is done with the material card of law2_PLAST_JOHNS and failure johnson…
25 Nov 2020 02:57 PM IST
DESIGNING OF AMERICAN CHOPPER BIKE USING SOLIDWORKS
OBJECTIVE: The objective of this project is used to create a model of different parts of the Chopper using Solidworks. To assemble the different parts modeled for the chopper. To create a Photorealistic model of the chopper and Render the model using Solidworks visualize. PART MODELING: Part Modeling you…
22 Jul 2020 06:27 AM IST
FRAME ASSEMBLY USING DIFFERENT CONNECTORS IN HYPERMESH
objective : The main aim of this project is to connect the different components of a frame assembly using different connectors in hypermesh. procedure: imported the assembly file in hypermesh software. since the components are surface checked for geometry cleanup. splitted the surfaces to attain fine mesh. generated 2d…
20 Jul 2020 04:04 PM IST
MESHING A SIDE DOOR OF A CAR USING HYPERMESH
OBJECTIVE: The main aim of this project is to mesh the side door of the car as per the quality criteria shown below. To assign thickness for the mesh elements. QUALITY CRITERIA: PROCEDURE: selected the radioss user profile for durability analysis. imported the model (.hm) file into the hypermesh. checked for any geometrical…
20 Jul 2020 03:51 PM IST
MESHING A BACK WHEEL PANEL OF A CAR USING HYPERMESH
OBJECTIVE: The main aim of this project is to mesh the back wheel panel of the car as per the quality criteria shown below. To assign thickness for the mesh elements. QUALITY CRITERIA: PROCEDURE: Selected the radioss user profile for durability analysis (say). Imported the back wheel panel model (.hm) file into the hypermesh…
20 Jul 2020 03:46 PM IST
MODELING AND RENDERING OF ROYAL ENFIELD CLASSIC 350 USING SOLIDWORKS
MODELING AND RENDERING OF ROYAL ENFIELD CLASSIC 350 USING SOLIDWORKSOBJECTIVE: 1.The main objective of this project is used to create a model of different parts of the royal Enfield classic 350 using Solid works. 2.To assemble the different parts modeled for the classic 350. 3.To create a photo-realistic view of the…
16 May 2020 10:34 AM IST
DESIGNING OF SUNSEEKER PREDATOR YACHT USING SOLIDWORKS.
SUNSEEKER PREDATOR YACHT OBJECTIVE: The main aim of this project is to create a surface model of different yacht parts. To assemble the parts modeled using the SolidWorks 2018 software. To create a photorealistic model of the yacht and render the model using the SolidWorks visualize software. PART MODELLING:…
11 May 2020 02:19 AM IST