Week 4-1D Element Creation Challenge

Answers:Aim: To extract mid-surface for the tube model and provide a connection with a sharing option at the tube joint locations by using ANSYS SpaceClaimCase1:Procedure: Import the tube joint model to the SpaceClaim graphical windowMeasure the thicknessMid Surfacing:Next, extract the mid surface for the tube joint by…

AIM Perform the simulation as per the cases given below. Case 1  Import the FAILURE_JOHNSON_0000.rad file and run the model as it is. Give the title name as Law2_epsmax_failure. Case 2 Import the case 1 rad file, named “Law2_epsmax_failure” and perform the simulation with failure plastic strain (EPS_p_max) and…

ANSWER:Import the file > Go To File > Import > Solver Deck > Element_Formulation-Shell-3_assignment_0000.rad1. Change the run time to 55 ms2. Change the number of animation steps during simulation to a minimum of 25 and maximum of 60The output time step has been selected 30 animation steps. Therefore,…

Aim For the given component, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned. Write a detailed report on your meshing process and also mention which method you used to extract the mid-surface along with the reason.   S.No  Quality…

OBJECTIVE: To Mesh the component by using the quality criteria below and assign thickness. S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2mm 6 Max. Length 8mm 7 Min angle Quad 45 8 Max angle Quad 135 9 Min angle Tria 20 10 Max angle Tria 120 11 Tria %  10 Target…

For the given MODEL 1, Create a Teramesh for Housing component with the following quality criteria. TetraMesh Generation Method: 2D to 3D Conversion Elements sizes: Min- 2 Units, Target- 5 Units, Max- 7 Units  Tet collapse: 0.15   MODEL-1 : Import the model given and work on it. Improve the Geometric errors if there are…

AIM: To achieve the given quality criteria        Target Element Length = 4 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 6 Units 7 Min angle Quad 45 8 Max angle Quad 135 9 Min angle Tria 20 10 Max angle Tria 120 10 Tria %  10 To mesh…

AIM: Target Element Length = 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7 Min angle Quad 45 8 Max angle Quad 135 9 Min angle Tria 20 10 Max angle Tria 120 10 Tria %  10 Objective - To generate…

AIM: Target Element size - 5 Units S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 3 Units 6 Max. Length 7 Units 7 Min angle Quad 45 8 Max angle Quad 135 9 Min angle Tria 30 10 Max angle Tria 110 10 Tria %  15 PROCEDURE: Download…

OBJECTIVE: To Mesh the component by using the given quality criteria below and assign thickness. S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 2mm 6 Max. Length 8mm 7 Min angle Quad 45 8 Max angle Quad 135 9 Min angle Tria 20 10 Max angle Tria 120 11 Tria %  10…

AIM:- a. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX- Dimension a= 12 mm                               dimension b=10 mm                        …

ABSTRACT:            The main objective of this challenge is to create connections for the given rear side door model and store them in separate PIDs using useful tools in ANSA. PROCEDURE:            There are two steps to be followed for deploying the connections,…

Aim: To achieve the 3d mesh for the given model and meet the quality criteria. Quality Criteria: S.No  Quality Criteria  Value  1 Target/Average length   1 2 Minimum Length  0.5 3 Maximum Length  2 Using tetra elements to mesh the Volumes defined in the model and checking for the below…

OBJECTIVE: S.No  Quality Criteria  Value  1 Target/Average length   1 2 Minimum Length  0.5 3 Maximum Length  3 4 Aspect  3 5 Warpage 15 6 Skewness 45 7 Jacobian  0.7 8 Minimum Quad Angle  45 9 Maximum Quad Angle  135 10 Minimum  Tria Angle  30 11 Maximum…

Procedure: Open the cad model in ansa pre proccesser. Check the geometry from the tools section mentioned as 'check'. Resolve the geometry issues. Generate the mid surface of the given cad model 'Manually' or 'Automatically'. Manually: Using the 'offset' option in the faces module. Automatic: Using the 'mid surfacing'…

Aim: To check the geometry of the given model. To find the mid surface of the given model. To generate a mesh with the given quality criteria of the given model. Given CAD model: Procedure: Open the cad model in ansa pre proccesser. Check the geometry from the tools section mentioned as 'check'. Resolve the geometry issues.…

Answer: Aim: To read the excel file given To perform the interpolation in the range of -17.3:0.1:0.9. Generate the interactive plot for the interpolated data and store them in a text file Code: clear; clc; % interpolation of voltage and current data D=xlsread('VI');% reading excel file data x=D(:,1); % voltage data…

Answers: 1)  Generator  Battery  Starter  Ignition coil  Ammeter  Foot selector switch  Breaker  Fuse  Current and voltage regulator   2) Generator:  An electric generator is a device that converts mechanical energy obtained from an external source into electrical…