Aim - To conduct the Rayleigh Taylor CFD simulation. OBJECTIVE: What are some practical CFD models that have been based on the mathematical analysis of Rayleigh Taylor waves? In your own words, explain how these mathematical models have been adapted for CFD calculations. Perform the Rayleigh Taylor…
JAYA PRAKASH
updated on 26 Oct 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by JAYA PRAKASH (11)
Week 9 - Parametric study on Gate valve.
Gate Valve Parametric Study Objectives To perform the parametric study on the gate valve by simulating the opening of gate valve ranging from 10mm to 80mm. To obtain the mass flow rate for each design point. Calculate the flow factor and…
16 Dec 2022 07:47 PM IST
Week 6 - CHT Analysis on a Graphics card
AIM: To perform steady-state conjugate heat transfer analysis on Graphics Card. To find the effect of different velocities on the temperature. Objectives: Run the simulation by varying the velocity from 1m/sec to 5m/sec for at least 3 velocities and discuss the results. Find out the maximum temperature…
03 Nov 2022 09:12 AM IST
Week 5 - Rayleigh Taylor Instability
Aim - To conduct the Rayleigh Taylor CFD simulation. OBJECTIVE: What are some practical CFD models that have been based on the mathematical analysis of Rayleigh Taylor waves? In your own words, explain how these mathematical models have been adapted for CFD calculations. Perform the Rayleigh Taylor…
26 Oct 2022 05:35 PM IST
Week 4 - CHT Analysis on Exhaust port
Aim: CHT Analysis on Exhaust port. Objective: The objectives will mainly focus on Give a brief description of why and where a CHT analysis is used. Maintain the y+ value according to the turbulence model and justify the results. Calculate the wall/surface heat transfer coefficient on the internal…
21 Oct 2022 07:58 PM IST
Week 3 - External flow simulation over an Ahmed body.
Aim: CFD simulation of the External flow over an Ahmed body. Objective: The objective of this project is to determine the aerodynamic forces on the Ahmed body such as drag and lift coefficient and wake flow around the body to perform the different …
19 Oct 2022 04:57 PM IST
Week 2 - Flow over a Cylinder.
Aim: To Simulate the flow over a cylinder and explain the phenomenon of Karman vortex street. Objective: 1. Simulate the flow with the steady and unsteady case and calculate the Strouhal Number for Re= 100 2. Calculate the coefficient of drag and lift over a cylinder by setting the Reynolds number to 10,100,1000,10000…
12 Oct 2022 05:10 PM IST
Week 1- Mixing Tee
Aim: To set up steady-state simulations to compare the mixing effectiveness when hot inlet temperature is 360C & the Cold inlet is at 190C. Used to find the k-epsilon and k-omega SST model for the first case and based on your judgment use the more suitable model for further cases. Given Data: Case 1 Short…
10 Oct 2022 09:54 AM IST
Week 7 - Simulation of a 1D Super-sonic nozzle flow simulation using Macormack Method
Aim: To Simulate the isentropic flow through a Quasi 1D subsonic nozzle by deriving both the conservation and non-conservation forms of the governing equations and solve them by implementing the MacCormack's technique using MATLAB. Objective: …
21 Sep 2022 11:13 AM IST
Week 5.1 - Mid term project - Solving the steady and unsteady 2D heat conduction problem
AIM: To solve the 2D heat conduction equation for steady and unsteady state by using the point iterative technique to using method of t Jacobi, gauss seidel, and successive over-relaxation for both implicit and explict method. Explanation: Heat Conduction: Heat conduction is the flow of thermal energy…
02 Sep 2022 04:41 PM IST
Week 3.5 - Deriving 4th order approximation of a 2nd order derivative using Taylor Table method
Objective: To derive the 4th order approximation of a second order derivative for central difference and skewed left and right didded difference method using taylor table method and to compute analytical derive and write functionin matlab to find range…
08 Jul 2022 06:11 PM IST