Draft in Mould - In engineering draft is the amount of taper for the mould or cast part perpendicular to the parting line or say tooling axis, it can be measured in degree. By applying the appropriate draft angle, the mould or the part will be easier to remove. Application require a minimum ½ to 1 degree,…
Ankosh Vasave
updated on 11 Feb 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by Ankosh Vasave (14)
Week 11 - Final project
OBJECTIVE 1. Creation of tooling direction and Perfom draft analysis on the class A surface from the inputs door trim panel, that is Map pocket upper lower, Lower substrate, Door armrest. 2. Creation of Class B and Class C surface and Solide body from the close surface. 3. Ceating attaching feature according to master…
29 Mar 2022 11:31 AM IST
Week 10- Assembly Workbench
QUICK RETURN MECHANINSM PART 1 In this part we created 5 sub parts which assembled togather to form this Quick return mechanism. BODY 1 this part is a base body where the reamining part is going to rest, created this part with a single sketch and a pad. created a sketch at the center of the all planes which is going to…
03 Mar 2022 04:37 PM IST
Week 9 - Project - Master Section Development
TOOLING AXIS To create tooling axis extract the lines from the master section create the , then using these master section create a point in center of that lines, then create a bisecting line using these lines and point and name it as Tooling Axis. then create SIDE CORE TOOLING AXIS To create side core tooling axis…
27 Feb 2022 07:25 PM IST
Week 9 - Project 1 - Door Applique Design with Engineering Features
PART 1 Creation Of Tooling Axis To create the tolling axis a take poing selct the class A surface, then create point over a surface in 0 distance. Then use line command select the point choos normal to surface option select the class a surface and create a line, name it as a Toooling AXIS. We are going to create every…
25 Feb 2022 06:31 AM IST
Week 9 - Attachment Feature Creation - Challenge 2
SCREW BOSS In plastic parts, bosses are typically used to assist in assembly, as a receptacle for a screw or threaded insert or as the locator for a mating pin on another part. Because of its function, a boss must have sufficient strength to do its job. This dictates a minimum size for the feature. Design rles…
21 Feb 2022 07:39 PM IST
Week 9 - Attachment Feature Creation - Challenge 1
RIB Ribs are a feature in plastic injection molded parts. They are thin extensions that run perpendicular from a wall or plane. They are commonly used to provide additional support and strength to a part. Thickness and location are essential to rib design. they can one or multiple over a component to provide high…
21 Feb 2022 02:18 AM IST
Door Arm Rest Week 8 Challenge
Draft Analysis in Catia The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of analysis is performed based on color ranges identifying zones on the analyzed element where the deviation from the draft direction at any point, corresponds to specified values. so…
18 Feb 2022 10:20 AM IST
Week 8 - Challenge 5 - Core & Cavity Design
Draft Analysis in Catia The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of analysis is performed based on color ranges identifying zones on the analyzed element where the deviation from the draft direction at any point, corresponds to specified values. so…
16 Feb 2022 06:16 PM IST
Week 8 - Challenge 4 - Coin Holder Design
Draft Analysis in Catia The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of analysis is performed based on color ranges identifying zones on the analyzed element where the deviation from the draft direction at any point, corresponds to specified values. so…
16 Feb 2022 06:59 AM IST
Week 8 - Challenge 3 - Switch Bezel Design
Draft Analysis in Catia The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of analysis is performed based on colour ranges identifying zones on the analized element where the deviation from the draft direction at any point, corresponds to specified values. There…
14 Feb 2022 06:49 AM IST
Week 8 - Challenge 2 - Base Bracket Design
DRAFT ANAYLYS AND MODELING OF BRACE BRACKET USING SURFACE MODELING To crate a tooling axis by Bisecting Method 1. Analise the given class A surface for in which direction the tooling axis can we create. 2. Create an intersection using YZ plane. Find the…
12 Feb 2022 08:40 PM IST
Week 8 - Challenge 1 - Draft Analysis on a Fan Cover
Draft in Mould - In engineering draft is the amount of taper for the mould or cast part perpendicular to the parting line or say tooling axis, it can be measured in degree. By applying the appropriate draft angle, the mould or the part will be easier to remove. Application require a minimum ½ to 1 degree,…
11 Feb 2022 02:41 PM IST
Radar Mast & Final Assembly of Yacht
********************** Design and Assembly of YACHT in Solidwork Aim & Objective Design and assembly of the yacht in solidework. To learn the surface modeling features in the solidwork. How to model and design using…
24 Dec 2021 12:01 PM IST
Photo Realistic Rendering
DESIGN AND MODELING OF AMERICAN CHOPPER IN SOLIDWORK AIM & OBJECTIVE❖ To learn interface and commands of solidworks.❖ To design American chopper, design its part individually, applying materials, applying decals and assemble all the parts in soliworks assembly.❖ How to do setting lighting,…
13 Nov 2021 12:34 PM IST