Q1. Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco 174357-2 (https://www.te.com/usa-en/product-2-174357-2.html?source=header-match)…
Hemant Sagar
updated on 05 Mar 2023
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by Hemant Sagar (27)
Week 12- Final project
Creation of CAD model considering following inputs as like in OEM and tier1 companies a) Class A surface b) Nominal thickness : Refer master sections c) Attachment strategy : Find a attachment strategy for the door panel complete work. Use Push pin with Dog house for Lower substrate – Door panel attachment…
01 Aug 2023 05:02 PM IST
Week 11 - Project - A pillar Design with Master Section
A-PILLAR DESIGN WITH MASTER SECTION AIM: To create the A Pillar Design with the master section given as the intersection sketch with the Class A surface and create the tooling axis and perform the Draft analysis for the final solid part. CLASS A SURFACE: Class A is an aesthetic surface with the highest quality finish.…
09 Jul 2023 10:28 AM IST
Week 10 - Challenge 3 - Door Trim Lower with Engineering Features
Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Create the Heat Stakes and the locators considering…
01 Jul 2023 01:34 AM IST
Week 10 - Challenge 2- Attachment Feature Creation (Dog House)
Create the Dog House for the Door Trim considering the design rules mentioned in the video. Consider the thickness of the part to be 2.5 mm. "C" is where the doghouse contacts the backside of the surface Doghouse wall thickness at the intersection of the part wall ( C ) should be 40% or less than the…
19 Jun 2023 03:50 AM IST
Week 10 - Challenge 1- Attachment Feature Creation (Ribs & Screw Boss)
Create the rib for the Drill Handle considering the design rules mentioned in the video. Create the Screw boss for the Drill Handle considering the design rules mentioned in the video. General Guidelines for Bosses: Draft - 0.5 degrees on the walls of boss Thickness - Typically…
07 Jun 2023 04:18 PM IST
Week 9 - Challenge 3 - Bumper
Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Take the Thickness of the component to be 3 mm INTRODUCTION:…
29 May 2023 09:07 AM IST
Week 9 - Challenge 2 - Switch Bezel Design
Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Take the Thickness of the component to be 2.5…
28 May 2023 06:41 AM IST
Week 9 - Challenge 1 - Base Bracket Design
Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Thickness of Plastic Part - 2.5 mm Creation of a part…
24 May 2023 05:37 PM IST
Week 7 Challenge - Assembly Workbench
In this week’s assignment, you will have to create 2 assemblies according to the content covered in the course videos. You will be provided with 2D diagrams of the components and you will have to first create the individual part files and then create a complete assembly of those part files in the assembly…
30 Apr 2023 11:39 AM IST
Project 2
Statement of assignment:Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required.Available connector 3D data can be used, or you can…
31 Mar 2023 04:43 PM IST
Project 1
Statement of assignment: Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required. Available connector 3D data can be used, or you can…
27 Mar 2023 12:19 AM IST
Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge
Q1. Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view. AIM- To prepare a flattened view of a previously created harness assembly OBJECTIVE- The objective of this project is to…
17 Mar 2023 01:21 AM IST
Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge
Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing, Check the bundle Continuity. Add snap of result in submission Add annotation to all connectors. Make an assumptions for annotations like connect 1 , 2 etc…
16 Mar 2023 04:48 AM IST
Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge
Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end) Download connector…
12 Mar 2023 08:27 AM IST
Wiring harness routing & packaging Rules Week 3 Challenge
Q1. Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P clamp Steps. Once the File is Downloaded, Open the File Using CATIA V5 Using the Part design model, we define entry, Exit, Base points, and Planes After determining…
07 Mar 2023 01:48 AM IST
Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge
Q1. Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco 174357-2 (https://www.te.com/usa-en/product-2-174357-2.html?source=header-match)…
05 Mar 2023 02:16 PM IST
Project 2 Thermal modeling of battery pack
For a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. To analyze temperature and life cycle parameters of the 10 cell series battery pack. Connect 10 cells in series analyze the response…
26 Feb 2023 12:04 PM IST
Project 1 Mechanical design of battery pack
Battery pack capacity: 18 kWh Cell: ANR26650M1-B Prepare a detailed battery pack drawing along with its enclosure. State your assumptions. ABSTRACT:- In this project, we are going to calculate the all parameters which are required for the build EV battery pack. We are going to use the Cell:…
23 Feb 2023 12:09 AM IST
Week 7 State of charge estimation
https://in.mathworks.com/matlabcentral/fileexchange/72865-design-and-test-lithium-ion-battery-management-algorithms 1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results 2.What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation…
16 Feb 2023 01:20 AM IST
Week 1 Understanding Different Battery Chemistry
Q1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it NAME ANODE CATHODE SEPERATOR ELECTROLYTE ANODE REACTION CATHODE REACTION OVERALL REACTION Lithium Cobalt Oxide (LCO) Graphite…
04 Feb 2023 02:16 PM IST
Project 2
Description:As discussed in Lecture 11, Project 2 deals with the development of a forward energy-based fuel consumption model of a P1 hybrid vehicle. This model is based on the conventional vehicle model from Project 1. The main goal of this project is to understand the functionality of a P1 hybrid and be able to model…
01 Feb 2023 06:46 AM IST
Project 1
Description:Project 1 deals with the development of a forward energy-based fuel consumption model of a conventional vehicle. The main goal of this project is to get familiar with the modeling process, writing scripts in Matlab, modeling in Simulink, analyzing data and generating plots. In this project, a typical midsize…
24 Jan 2023 01:17 AM IST
Project 1
Develop a double-acting actuator model using Simscape Multibody and Simscape components. The mechanical system of the cylinder needs to be built using Simscape Multibody library components / blocks, and the hydraulic system needs to be modelled using Simscape library physical components. CYLINDER MODEL …
10 Jan 2023 04:52 PM IST
Project - Position control of mass spring damper system
Q1.Obtain the transfer function of a mass spring damper system and use it in the model. Add a PID controller to adjust the force on mass so that its position follows a reference signal. Take m = 3.6; %kg k = 400; %N/m c = 100; %Ns/m …
21 Dec 2022 02:11 PM IST
Project - Data Handling and Interpolation
Project : In a laboratory experiment, data of voltage and current has been recorded and the same is attached in an excel file ( Click on this link VI.xlsx ). Read the excel file in the Matlab program and perform the interpolation in the range of -17.3:0.1:0.9. Generate the interactive plot for the interpolated…
22 Nov 2022 03:36 PM IST
Project - Data Handling and Interpolation
Project : In a laboratory experiment, data of voltage and current has been recorded and the same is attached in an excel file ( Click on this link VI.xlsx ). Read the excel file in the Matlab program and perform the interpolation in the range of -17.3:0.1:0.9. Generate the interactive plot for the interpolated…
20 Nov 2022 03:33 AM IST
Project - Analysis of a practical automotive wiring circuit
Q1-major elements in automotive wiring diagram is 1-junction box,2-generator,3-current and voltage regulator, 4-ignition coil,5-distributor, 6-starter, 7-ammeter, 8-ignition switch, 9-battery, 10-fuse Q2-1-starter (also starter motor) is a device used to rotate (crank) an IC engine so as to initiate…
12 Sep 2022 05:22 PM IST